Preface; Introduction; Product Description - PLYMOVENT MFD Manuel Opérateur

ENGLISH

PREFACE

Using this manual
This manual is intended to be used as a work of reference for
professional, well trained and authorised users to be able to
safely install, use, maintain and repair the product mentioned
on the cover of this document.
Pictograms and symbols
The following pictograms and symbols are used in this manual:
TIP
Suggestions and recommendations to simplify
carrying out tasks and actions.
CAUTION!
Procedures, if not carried out with the necessary
caution, could damage the product, the workshop or
the environment.
WARNING!
Procedures which, if not carried out with the necessary
caution, may damage the product or cause serious
personal injury.
WARNING!
Denotes risk of electric shock.
WARNING!
Important warning to prevent fire.
Text indicators
Listings indicated by "-" (hyphen) concern enumerations.
Listings indicated by "•" (bullet point) describe steps to perform.
Service and technical support
For information about specific adjustments, maintenance or
repair jobs which are not dealt with in this manual, please
contact the supplier of the product. He will always be willing to
help you. Make sure you have the following specifications at
hand:
- product name
- serial number
These data can be found on the identification plate.
1

INTRODUCTION

1.1 Identification of the product
The identification plate contains, among other things, the
following data:
• product name
• serial number
• supply voltage and frequency
• power consumption
1.2 General description
The MFD is a mobile filter unit with integrated fan that provides
extraction and filtration for use with a flexible extraction arm or
extraction hose.
The MFD features an aluminum spark arrester and a square
disposable cellulose filter cartridge. This filter cartridge is
provided with a precoat to extend the lifespan and increases
initial operating efficiency of the filter. A filter pollution indicator
indicates when filter replacement is required.
Thanks to the four transport wheels (two of which are swivel
casters), the MFD is extremely suitable to be used in relatively
small facilities or near sources of pollution without a fixed
location.
Extraction arm/hose to be ordered separately.
1.3 Product combinations
In order to operate the machine, selection of one of the
following products is required:
0507240010/010513/I MFD
- Flex-3 (extraction arm)
- Flex-4 (extraction arm)
- UltraFlex-3 (extraction arm)
- UltraFlex-4 (extraction arm)
- SUS-5/203 (extraction hose)
1.4 Options and accessories
The following products can be obtained as an option and/or
accessory:
- FAC-50 (activated carbon filter)
- TRK-MFD (transformer relay kit; required in case of WL or WL-
AST in connected extraction arm)
- EXS-5/203 (extension hose to SUS-5/203)
1.5 Technical specifications
Dimensions L x W x H
Weight
Power consumption
Unrestricted airflow
Net extraction capacity
Motor speed
Filter class:
- spark arrester
- main filter DuraFilter FCC-50
Filter surface
Insulation class
Protection class
Refer to the available product data sheet for detailed
specifications.
1.6 Ambient conditions
Min. operating temperature
Nom. operating temperature
Max. operating temperature
Max. relative humidity
1.7 Transport of the machine
The manufacturer cannot be held liable for any transportation
damage after delivery of the machine. Always handle the
machine and the accompanying extraction arm/hose with care.
Always completely dismount the extraction arm/hose before
transport. Dismount the arm/hose by executing the mounting
procedure in reverse order. Subsequently the machine and the
arm/hose can be transported on a pallet in the original packing.
To prevent damage, prevent the machine and the arm/hose
from shifting on the pallet.
2

PRODUCT DESCRIPTION

2.1 Components
The machine consists of the following main components:
Fig. 2.1
A control panel
B control panel cover
C filter cover
D filter sealing plate
E star knob
F spark arrester (pre filter)
1210 x 810 x 900 mm
90 kg
0,75 kW
3
2400 m /h
3
1250 m /h (clean filter)
2800 rpm
- G3 according to DIN-
EN 779
- M according to NEN-
EN- IEC 60335-2-69
2
50 m
F
IP 50
5°C (41°F)
20°C (68°F)
45°C (113°F)
80%
EN - 2