Operation; Fill With Water; Basic Settings; On / Off Switch On / Off - ProfiCare PC-VL 3069 LB Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 22

Operation

Fill with Water

CAUTION:
Do not fill the water tank with water from clothes dryers
and water with additives (such as scented oils, perfume,
softeners, or other chemicals). Doing so may damage the
appliance.
NOTE:
• Only use distilled or boiled, cold tap water without
additives.
• Replace the water every 3 - 4 days, even if it has not
yet been used.
• If the appliance has not used for long periods, remove
the water from the water tank and from the base of the
humidifier.
• Pull the end of the tube with the tank cap out of the water
tank.
• Lift the tank from the base of the humidifier and turn it
over. The filling hole is located on the bottom of the tank.
• Turn the tank cap and fill the water up to ca. 1 centimeter
below the rim. The tank holds around 3 litres.
• Close the cap again and place the tank back onto the
base.
• Place the end of the tube with the tank cap onto the
water tank.
NOTE:
Take note of the recess on the tank cap (see assembly
instruction, item 21).

Basic Settings

Set the blower inclination angle before starting the appli-
ance. You can adjust the inclination angle by tipping the
blower casing with both hands.
NOTE:
• The inclination angle amounts to approx. 10 °.
• The tube above the switch housing must not "sag" due
to the inclination of the blower. Water which collects in
the tube prevents the formation of mist.
You can operate the appliance using the remote control as
well as the buttons on the switch housing. The functions are
identical.
NOTE:
The LED´s on the switch housing indicate the settings.
48
PC-VL3069LB_IM

ON / OFF Switch ON / OFF

Use the ON / OFF button to switch the appliance on or off.
NOTE:
• When switching on for the first time after you have
connected the mains plug to the mains outlet, the fan
works in NOR (normal) mode with a low speed (LO).
• After switching off and on again using the ON / OFF
button, the appliance continues working in the last set
mode.

SPEED Speed

Press the SPEED button to select one of the three different
speeds:
• LO
low
• MI
medium
• HI
high

TIMER Timer

If you want the timer to switch the appliance off, press the
TIMER button.
NOTE:
Every press of the TIMER button increases the operating
time by 30 minutes.
Maximum shut-off time: 7.5 hours.

MODE Wind Change Functions

The appliance has the two special functions: NAT (NA-
TURE) and SLE (SLEEP). The speed of the fan buries
between the functions.
Press the MODE button to switch these functions on.
NAT
Natural Mode
• If the HI (high speed) setting is selected, the speed
alternates between high– medium – low – off.
• If you have selected MI (medium speed), the speed
alternates between medium – low – off.
• In the LO (low speed) setting, the speed alternates
between low - off.
SLE
Sleep Mode
• If HI speed is set: The fan works in the first 30 minutes
as in "Natural Mode" at the HI speed setting. In the sub-
sequent 30 minutes the fan works as in "Natural Mode"
at the set MI speed. For the remaining time the fan works
as in "Natural Mode" at the speed setting LO.
• If MI speed is set: The fan works for the first 30 minutes
as in "Natural Mode" at the speed setting MI. For the
remaining time the fan works as in "Natural Mode" at the
speed setting LO.
• If LO speed is set: Switching between low speed and
shut-off of the fan as in "Natural Mode".
NOR
Normal
• Select the NOR (NORMAL) function to return to normal
operation.
17.09.19

Publicité

Table des Matières
loading

Table des Matières