cartronic RC Pocket Drone 2.4 GHz Notice D'utilisation page 6

GB / IE / NI
A Inserting the batteries
Please charge your drone before using it for the first time. After a charging period of approx. 30
minutes the drone can fly for approx. 8 minutes.
Charging the drone
There are 2 options for charging.
B1 Charging via PC or USB power supply
Switch the drone to OFF. Connect the drone to your PC / USB power supply using the USB charging
cable (5 V ± 0,5 V). The light-emitting diode in the USB connector first lights up red, then goes out
after about 1 second and lights up red again, when the charging process is complete.
B2 Charging via transmitter / PUSH UP CHARGING
Switch the drone to OFF. Insert the plug into the charging socket of the drone. The LED in the remote
control flashes red and turns to steady green when charging is complete.
C
Attaching the guards
D Inserting the control levers
E1
Pairing the remote with the drone
First set the ON / OFF switch of the drone to ON and place it on a flat surface. Then turn on the remote
control at the Power On / Off switch. The indicator light will initially flash red and then turn solid red.
If the pairing fails, turn off the drone and remote control and repeat steps 1 and 2.
E2 Calibrating the drone
Move both joysticks to the bottom right. Calibration starts when the indicator lights on the drone
are flashing. As soon as the flashing stops, the calibration has taken place.
Note: Please recalibrate before every start.
E3 Unlock the drone
Before starting, unlock the drone by moving the left joystick down to the left and the right joystick
down to the right. The propellers start to turn. With repeating the movement the drone is locked
again.
Flight functions
Please read the entire manual carefully and familiarize yourself with all the drone control options
before flying the aircraft.
F1
Floating up and down
Move the throttle lever forwards and backwards.
F2 Floating forward and backward
Move the direction lever forwards and backwards.
F3
Rotating left and right
Move the throttle lever left and right.
F4 Float sideways
Move the direction lever left and right.
Trim
* Right / Left trim
If the drone drifts right or left during takeoff, use these keys for correction (for example, trim to the
right if the drone drifts to the left)
** Forward / Reverse trim
If the drone drifts forwards or backwards during takeoff, use these keys for correction (for example,
trim forward if the drone drifts backwards)
G1
Turbofunction
The drone will fly faster when the turbo function has been activated. Switching on: Press the throttle
lever (2x beep) - Switching off: Press the throttle lever again (1x beep). The low speed is better
for beginners.
G2
3D Looping
While the drone is in the air, push in the direction lever. You will hear a beep. Then move the joystick
quickly in one direction. The drone performs exactly in this direction a 3D flip. Warning: For this
action, the drone needs enough space around it to avoid collisions or accidents. If the battery is
already quite discharged, the indicator lights will flash and the execution of a 3D flip is no longer
possible.
G3 Automatic start / automatic landing
Start: After unlocking the drone and while it is on the launch pad, press the „TAKE OFF / LANDING"
button. You will hear a beep. The drone takes off and floats in the air.
Landing: While the drone is in the air, press the „TAKE OFF / LANDING" button. After that, the
drone lands automatically.
Important note: While the drone automatically launches or lands (about 2 sec), no height
control by hand is possible.
G4 Fast rotation
While the drone is in the air, briefly press the „ROTATION / EMERGENCY STOP" button. A beep
sounds and the drone begins to turn at high speed. To stop the rotation, press the „ROTATION /
EMERGENCY STOP" button again.
Important notes: While the drone is in fast rotation, no flight control is possible. If the drone is
still to be controlled in fast rotation, activate the „Headless" function before using the „Fast Rotate"
function.
Warning: For this action, the drone needs enough space around it to avoid collisions or accidents.
If the battery is already quite discharged, the indicator lights will flash and the function „Fast
rotation" is no longer possible.
Emergency Stop
To stop the drone immediately in an emergency, press the „ROTATION / EMERGENCY STOP" button
for about 1 second. The engines then stop immediately.
Warning: If you use the emergency function, the drone crashes.
G5 Headless Function and Return Function
A) Headless function: The prerequisite for activating the headless function is that the drone
was first coupled to the remote control and calibrated. The headless function means that from
the pilot's point of view, the drone always follows exactly the direction of the steering direction,
regardless of how it is turned in the air in relation to the pilot.
Place the drone on a flat, level surface. The head of the drone is pointing away from the pilot and
the other end toward the pilot. Briefly press the headless mode button once. The remote control
beeps at constant intervals indicating that the headless function is now active. Now you should be
able to control your drone with the headless function. To end the headless function, briefly press
the headless mode button once. A beep indicates that the function is now OFF.
B) Return function: While the drone is in the air, long press the Return key and the drone will
return to the pilot. Return direction
Important notes on headless and return function
1. When pairing the drone with the remote, make sure that the head of the drone is pointing away
from the pilot and the other end towards the pilot (and the remote control).
2. When the headless or return function is activated, the pilot should not move around because the
drone flies to the relative location of the pilot with whose remote control it is connected, and not
exactly where the remote control is located.
3. In conclusion, our recommendation is that the pilot stays in the same position and looks in the
same direction as the drone was coupled and aligned (head away from the pilot).
Further notes
If one propeller does not move while the others are spinning, or has a different number of revolu-
tions, the engine of this propeller could be defective. During use, the motors as well as the control
board heat up. Let the drone cool for approximately 10 minutes after use to allow for permanent
stability of the individual components.
In case the drone would have to be landed in a further removed or an unsafe place during flight due
to a nearly depleted battery, our drones are equipped with a warning function. If the battery power
will soon be insufficient, the LED indicator will start flashing permanently. The pilot now has enough
time to fly the drone directly back and charge the battery.
Troubleshooting and FAQ:
Please use the following internet link:
http://cartronic.eu/de/Haeufige-Fragen/FAQ-Quadcopter
For more exciting products
visit our online shop at:
www.cartronic.eu
– 6 –
RC Pocket Drone 2.4 GHz
41950