SOLIS 8453 Mode D'emploi page 35

OPERATION
▲ ▲
1. Check if the Solis Citrus Juicer has been assembled correctly in the described
way. Place a glass or another container underneath the juice spout before start-
ing to juice.
2. Now make sure that the juice spout is folded out, meaning it is in the position
for pouring.
3. Cut the citrus fruit in two halves. To squeeze juice more effectively, you should
cut the fruit laterally, not lengthwise from end to end.
GB
Note: Some citrus fruits, e.g. mandarines, might have thicker ends. To ensure
optimal contact to the juicing cone, it is recommended to clip the pointed ends
with a knife.
4. Connect the power plug to a suitable wall outlet.
5. Place one half of the citrus fruit, with the cut side facing down, on the juicing
cone and press the fruit onto the spike of the juicing cone.
Caution: If you apply too much pressure, you engage the automatic activation
and the juicing cone starts rotating!
6. Take the lever handle of the press arm and push the lever press arm down slowly
in one smooth movement, until the squeezing cone comes into contact with the
fruit skin. Once this contact is made and some pressure is applied, the motor will
start automatically and the juicing cone will begin spinning. The juice is squeezed
from the fruit and runs through the juice spout into the glass resp. the container.
The pulp and the pips are collected in the pulp filter.
7. As the Solis Citrus Juicer works very effectively, it will only take a few seconds
until one fruit half is juiced. After a short time, you can return the lever press arm
into the highest position and the motor will stop automatically.
8. Take the squeezed-out fruit half from the juicing cone and, if necessary, empty
out the pulp filter resp. repeat steps 5 to 7 to juice the other fruit halves.
Caution:
Do not apply too high pressure to the press arm, the pressure should not exceed
● ▲
3 kg. Press for a maximum of 15 seconds and then stop applying pressure for
15 seconds.
If the appliance has been in use for 5– 6 minutes, you should take a break of
● ▲
10 minutes in any case.
68
Notes:
The pulp filter should be emptied once it is filled with pulp and pips.
● ▲
If you want to empty the pulp filter while juicing, pull the power plug, pivot
● ▲
the lever press arm to the highest position, fold up the juice spout and carefully
remove the juicing cone and the pulp filter with the juice collector. Empty and
rinse the filter and the juicing cone and reinstall everything into the appliance
before plugging it back in and starting to juice again.
The pulp filter should never be too full, as this hinders the appliance from func-
● ▲
tioning optimally resp. might cause damage to it.
Should the diameter of the fruit you wish to juice be too large for the squeezing
● ▲
cone, you can leave the lever press arm folded up and grab the fruit half with
your hand. Like that, you can juice basically every citrus fruit.
DI S ASSEMB LI NG THE AP PLI ANC E
▲ ▲
1. Always disconnect the power plug from the wall outlet first.
2. Push the lever press arm up, away from the motor base, until it reaches the
highest position. Close the juice spout by folding it up into the no-drip position.
3. Hold the lever press arm and remove the squeezing cone by pulling it sharply
out of the lever press arm.
4. Carefully lift the juice collector with the pulp filter and the juicing cone. Remove
the juicing cone and the pulp filter from the juice collector over a sink so that the
pulp leftovers can be easily removed. Then, clean the single parts as described
in the „Cleaning and Care" section on page 71.
5. Should a little bit of juice drip onto the work surface, please always wipe it off
immediately to prevent the surface from being damaged.
GB
69