Stanley SUPER 180 TIG LIFT Manuel D'utilisation page 4

The product is a portable, lightweight, single-phase 230 V,
50/60Hz welder with inverter technology. It allows MMA welding
with all electrodes type. The model allows TIG welding of the
most metals except the aluminium and alloys. Can be connected
to power generators with power equal to or higher than that
reported in Table 2. It is equipped with "HOT START", "ARC
FORCE" and "ANTI STICK" functions (for more details please
refer to the GENERAL PART manual included in the package).
DESCRIPTION OF THE MACHINE
Fig 1
1. Welding current Knob
2. Negative socket(-)
3. Positive socket (+)
4. Thermal protection LED indicator
5. LED indicator power on
6. selector TIG-MMA (only for the model TIG)
7. ON-OFF switch
8. Power Cord
INSTALLATION
The installation must be made by trained personnel in compliance
to the standard IEC 60974-9 and the current and local legislation.
To lift the machine it must be used the handle positioned on top of
the product with the machine in OFF position. The input voltage
must match the voltage indicated on the technical plate located on
the product. Use the machine on electric system having supply
features and power protection (fuse and / or differential switch)
that are compatible with the current required for its use. For more
details see the information on the plate placed on the machine.
TURN ON
Warning: Use all precautions required in the safety general
manual before operating the welder, reading carefully the risks
MAINTENANCE
Refer all servicing to qualified personnel.
Anomalies
The device does not deliver any current
and the yellow indicator LED of thermal
protection lights up.
The device is on but it does not
deliver any current.
Your unit does not weld correctly.
Instable arc
The electrode melts
This Model is without PFC device and do not comply with IEC 61000-3-12. If they are to be connected to a low-voltage
mains supply, it is the responsibility of the user to ensure they can be connected. If necessary consult the operator of
your electrical
distribution system
This welding machine is for professional use only and is reserved for the industry.
ENGLISH
associated with the welding process.
ELECTRODE WELDING (MMA)
Note: You must disconnect the earth clamp to the metal work
piece just after switching off the welding machine.
TIG WELDING (only for the TIG type)
1.
torch to the poles of the device; choose the polarity (forward or
reverse) in relation to the type of material to be welded
2.
3.
4.
5.
6.
valve
7.
the welder
8.
between the two phases
Stopped the welding, turn off the machine and close the gas valve.
THERMAL PROTECTION
In case of overheating of the machine the yellow LED indicates
that the thermal protection is on, you can start to weld it when the
LED is off
Causes
MMA
The welder thermal
protection has turned on.
The cable of the earth
clamp or electrode holder
is not connected to the
welder.
Polarity error
TIG
-)Default coming from the
tungsten electrode
-)Too important gas flow
rate
Polarity error
4
1. Connect the connectors of the earth clamp and electrode
holder to the poles of the device; choose the polarity
(forward or reverse) depending on the coating of the
electrodes (for more information see the information on
the electrodes packaging).
2. Connect the earth clamp to the work piece and insert the
electrode in the electrode holder
3. Connect the power cord to the power supply and turn on
the welder
4. Select the welding current as a function of the type of
electrode selected (Tab. 1).
5. Start the welding operation using all the necessary
protections to security.
Connect the connectors of the earth clamp and of the
Connect the earth clamp to the work piece
Connect the torch gas tube to the gas cylinder
Select the TIG mode
Select the welding current
Select the gas flow of the gas cylinder and open the torch
Connect the power cord to the power supply and turn on
Use the torch to weld as in the following without a puse
Touch the piece with the electrode
Lift the electrode from the piece
about 2-5 mm
Remedies
Wait for the end of the cooling
time, around 2 minutes. The
indicator led turns off.
Turn off the machine and check the connections.
. Check the polarity advised on the
electrodes packaging.
-) Use a tungsten electrode with the
adequate size
-) Reduce gas flow rate
Check that the earth clamp is really
connected to +