essentiel b ECHSC1b Notice D'utilisation page 18

Setting button
p
ress the button once to set the tiMer
Press the button once to set an operating time. The "h" indicator light flashes on
1.
screen.
Use the "+" (increase) and "-" (decrease) buttons to increase or decrease the heater's
2.
operating time.
You can define an operating time between 1 and 24 hours. Every time the "+" or "-"
3.
button is pressed, the operating time increases or decreases by 1 hour.
At the end of the countdown, the heater automatically switches to standby mode.
4.
n :
otes
Press and hold the "+" or "-" button on the control panel to quickly scroll through the time.
•
Make the setting while the "h" indicator light is flashing on screen, because after 5 seconds
•
the screen returns to the requested temperature display.
Do not turn off the appliance by setting the "I/0" switch located at the rear of the appliance
•
to position "0" (off) as this will cancel the timer.
To change the operating time, repeat steps 1 to 3 above and select a different duration.
•
To cancel the timer, press the
•
"0h". The heater will therefore work indefinitely.
p
ress the button twice to set the teMperAture
Press the button twice to define an operating temperature. The "°C" indicator light
1.
flashes on screen.
Use the "+" (increase) and "-" (decrease) buttons to increase or decrease the desired
2.
temperature.
You can define a temperature of 5°C to 35°C. The default temperature is 22°C. Every
3.
time the "+" or "-" button is pressed, the temperature increases or decreases by 1°C.
n :
otes
Press and hold the "+" or "-" button on the control panel to quickly scroll through the time.
•
Make the setting while the "h" indicator light is flashing on screen, because after 5 seconds
•
the screen returns to the requested temperature display.
The heater automatically stops when the room temperature reaches the set temperature. It
•
restarts when room temperature drops.
34
V.2.0
use
button, then press the "-" button until the screen shows
If room temperature is below -10°C, the screen shows "
•
equal to or higher than 40°C, the screen shows "
temperature if the temperature ranges from -10°C to 40°C.
If you have programmed a timer and a temperature, the screen alternately shows the timer
•
and the requested temperature every 30 seconds. If you have not programmed a timer, the
screen only shows the room temperature.
If the heater is in standby mode and you press the
•
operate again with the previously defined settings (except for the timer). However, if you
turn the heater back on while it was running on high
power for the first 20 seconds before automatically switching to high power.
After one minute of inactivity on the control buttons, the brightness of the screen fades.
•
Brightness returns to normal when you press any button.
p
rogrAMMing A delAyed stArt
When the heater is in standby mode (plugged in and the "I/0" on/off switch on the back of
the appliance in position "I" ), you can program a delayed start.
CAUTION: never
•
unattended when in use.
Beforehand, set the desired temperature as described in "
1.
" section (when you turn the appliance back on, it retains the previous
to set the tiMer
temperature setting) and switch the appliance to standby mode by pressing the
button.
Press the button once. When "0h" flashes on screen, use the "+" / "-" buttons to
2.
set the delayed start. "h" is then displayed with the selected number of delayed hours.
The heater will switch on automatically and indefinitely at the end of the countdown
3.
you have defined.
To cancel the delayed start, press the
•
shows "0h". The heater returns to standby mode. (You can also switch the appliance off
using the "I/0" on/off switch).
LO
" (cold); if room temperature is
H I
" (hot). The screen shows the room
button again, the appliance will
power, it will run on medium
leave the appliance
p
ress the button twice
button, then the "-" button until the screen
V.2.0
35
use