Ryobi R18PD5 Traduction Des Instructions Originales page 3

Safety, performance, and dependability have been given
top priority in the design of your percussion drill.
INTENDED USE
The percussion drill is intended to be used only by adults
who have read and understood the instructions and
warnings in this manual, and can be considered responsible
for their actions.
The percussion drill is intended to be used in drilling into
various materials, including wood, metal, and plastic using
a drill bit having a diameter of less than 13 mm. When in
impact mode, the percussion drill can be used in drilling
masonry and similar materials. When in screw driving
mode, the percussion drill can be used in driving screws.
Do not use the product in any way other than those stated
for intended use.
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result in
Save all warnings and instructions for future reference.
PERCUSSION DRILL SAFETY WARNINGS
Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool.
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Do not operate on materials (e.g., asbestos) that
present a health hazard.
Switch off the product immediately if the bit stalls. Do
not switch on the product again while the bit is stalled,
as doing so could trigger a sudden recoil with a high
reactive force. Determine why the bit stalled and rectify
this, paying heed to the safety instructions.
The possible causes may be:
– it is tilted in the workpiece
– it has pierced the workpiece
– the product is overloaded
Sawdust and splinters must not be removed while the
product is running.
When working in walls, ceilings, or floors, avoid
electrical cables and gas or water pipes.
Secure your workpiece with a clamping device.
Ambient temperature range for tool during operation is
Ambient temperature range for tool storage is between
The recommended ambient temperature range for the
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
damage due to a short circuit, never immerse your
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
Ambient temperature range for battery during use is
Ambient temperature range for battery storage is
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The operator should pay particular and additional
attention to these points in order to reduce the risk of
exposure.
when using the product.
the instructions on risk reduction in this manual.
Electric shock after contact with hidden wires – Hold the
product only by insulated surfaces.
product – Wear suitable protection depending on type
of dust.
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. These are measures that can be taken by the
operator to possibly reduce the effects of vibration:
Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
contributing to Raynaud's Syndrome.
After each period of operation, exercise to increase
blood circulation.
Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English | 1