Télécharger Imprimer la page

Hama EWS-1400 Mode D'emploi page 6

Masquer les pouces Voir aussi pour EWS-1400:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
Note
• When installing the measuring station, ensure that it is protected
from direct sunlight and rain.
• The international standard height for measuring air temperature
is 1.25 m (4 ft) above ground.
Warning
• Buy special or suitable installation material from a specialised
dealer for wall-mounting.
• Ensure that no faulty or damaged parts are installed.
• Never apply force during installation. This could damage the
product.
• Before installation, ensure that the chosen wall is suitable for the
weight to be mounted, and make sure that there are no electrical
wires, water, gas or other lines at the installation site on the wall.
• Do not mount the product above locations where persons
might linger.
5.1. Base station
• Use the base to position the base station on a level surface.
• Alternatively, you can install the base station on a wall using the
opening (24) on the back.
5.2. Measuring station
• You can also position the measuring station on a level outdoor
surface.
• We recommend installing the measuring station securely on an
outdoor wall (28).
• Install an anchor, screw, nail, etc. in the wall of your choice.
• Hang up the base/measuring station using the opening (24/28)
intended for this purpose.
6. Operation
Note
Hold down the + button (18) or the – button (19) to select the
values faster.
6.1. Connection to the measuring station
• After you insert the batteries, the base station automatically
searches for a connection to the measuring station and performs
initial setup.
Note
• Initial setup takes approx. 3 minutes.
• During connection, the wireless symbol on the measuring station
will ash (2).
• Do not press any buttons during setup. Otherwise, values may
not be transmitted correctly and there is a risk of value errors
and inaccuracies.
• The setup process is completed when the indoor (5/6) and
outdoor (1/16) measurement data is displayed
4
• If the base station still does not receive a signal from the measuring
station, press and hold the SEARCH button (21) for approx. 3
seconds to start the manual search for the signal.
6.2. Basic and manual settings
Automatic setting using the DCF signal
• After the rst time the base station is switched on and successful
transmission is established between the base station and the
measuring station, the clock will automatically search for a DCF
signal. During the search, the wireless symbol (8) will ash.
Display
Display ashing
Displayed continuously
No display
• If the station still does not receive a signal, press and hold the –
button (19) for approx. 3 seconds to start the manual search for the
DCF signal. The wireless symbol (8) will start to ash.
Note – Time settings
• The search process takes about 7 minutes. If the search fails, it
ends and is repeated at the next clock hour.
• In the meantime you can, however, set the time and the date
manually.
• The clock automatically continues to search for the DCF signal
on a daily basis (between 1:00 a.m. and 5:00 a.m.). If the
signal is received successfully, the manually set time and date
are overwritten.
• Press and hold the – button (19) again for approx. 3 seconds to
stop the manual search.
Note – Summer time
The clock automatically switches to summer time.
the display as long as summer time is activated.
(Manual) settings
• Press and hold the – button (19) for approx. 3 seconds to stop the
search for the DCF signal. The wireless symbol (8) goes out and you
can set the time manually.
• Press and hold the MODE button (17) for approx. 3 seconds to
make the following settings one after the other:
• 12/24 hour format
• Time zone
• Hours
• Minutes
• Year
• Month
Searching for the DCF signal
Active
Successful – signal is being received
Inactive
appears on

Publicité

loading

Ce manuel est également adapté pour:

0018630600136259