Publicité
10
Operator Instructions
6
1. To Start the Unit
Press and hold
for three seconds. The unit will start and the air temperature will be displayed.
Important to note that the ability to increase and decrease the set point is not a function available to the user on the
freezer rooms as the set point is fixed.
2. To Check Storage Temperature Set Point
i set
Check set point by pressing the button
Factory Temperature Set Point- Refrigerator temperature +1°C to +4°C. Freezer temperature -18°C to -21°C.
Exit from set up occurs automatically after 10 seconds if no button is pressed.
3. Manual Defrost
❄
To initiate a manual defrost press and hold
F
ee
On completion of the defrost
will be displayed until the cabinet temperature is achieved and then it will revert to
displaying the normal cabinet temperature.
4. Set Unit to Standby.
OFF
Press
display shows
(standby indication)
Standby Indication
This indication is displayed while the unit is not operating but with mains power applied to the unit. This mode may be used for
internal cleaning regimes and short periods when the unit is not required.
For extended periods of inactivity the power supply should be turned off at the mains.
Alarms and Warnings
7
High temperature alarm
Will be displayed. The alarm will sound but can be
HI
silenced by pressing any of the buttons, however it
will return after the pre-set designated period. The
unit returning to normal operating temperature will
automatically cancel the alarm.
Low temperature alarm.
Will be displayed. The alarm will sound but can be
LO
silenced by pressing any of the buttons and the unit
will continue to operate, however it will return after
the pre-set designated period. The unit returning to
normal operating temperature will automatically
cancel the alarm.
Door open alarm
Will be displayed. The alarm will sound but can be
DO
silenced by pressing.
The display will continue to display the alarm message until
cancelled by shutting the door. If the alarm cannot be
cancelled by doing this call your Foster Authorised Service
Company.
8
Cleaning Instructions
Important: Before cleaning the power supply should be turned off
at the mains. Cared for correctly, stainless steel has the ability to
resist corrosion and pitting for many years.
The following weekly cleaning regime is recommended:
a. Exterior: use a proprietary stainless steel cleaner following the
manufacturers instructions.
b. Interior: Wash with soapy water, rinse and dry thoroughly.
WARNING: High alkaline cleaning agent or those containing
bleaches, acids and chlorines are very harmful to stainless steel.
Corrosion and pitting may result from their accidental or deliberate
application. If any of these liquids should come into contact with
the unit during general cleaning, wipe down the affected area with
clean water and rub dry.
Never use wire wool or scouring powders on stainless steel or
aluminum surfaces.
After cleaning allow the unit to reach its normal operating
temperature before reloading with product. During usage all spills
should be wiped clean immediately but care should be taken not to
touch the interior of freezer units as warm skin can 'freeze' to metal.
english
GB
EF
❄
will be displayed release.
Air Temperature Probe Failure.
Displayed. The alarm will sound but can be silenced
E1
by pressing any button. There is no further action
that can be taken by the user in this instance.
During this period the unit will continue to operate
but have a reduced performance call your Foster
Authorised Service Company.
Evaporator Temperature Probe Failure.
(Automatic Defrost Cabinets Only)
Displayed. The alarm will sound but can be silenced
E2
by pressing any button. There is no further action
that can be taken by the user in this instance. During this
period the unit will continue to operate satisfactorily, but
this failure will have an effect on the defrost and
therefore efficiency if allowed to continue call your Foster
Authorised Service Company.
Door Gaskets
These should be inspected on a regular basis and replaced if damaged. To
clean, wipe with a warm damp soapy cloth followed by a clean damp cloth
and finally thoroughly dry before shutting the door.
Condensor Cleaning
Clean the condenser, located in the unit compartment, when it
becomes dirty.
Important: Disconnect the mains electrical supply to the machine
prior to cleaning the condenser. Clean the condenser using a soft
brush or vacuum cleaner.
NOTE: if there are any stubborn grease deposits etc left on or
through the condenser call your Foster Authorised Service Company
to carry out a full service.
Once the condenser has been cleaned switch the unit on. Failure to carry out
this action may invalidate the warranty of the condensing unit.
Airflow
Do not obstruct the airflow through out the cabinet interior.
Air inlet and outlet duct should not be obstructed with cardboard
boxes etc. as this may result in the evaporator icing up causing a loss
of performance and temperature rise within the cabinet. Do not place
unfrozen product in to frozen food cabinets, as the warmth from the
product will affect the temperature of the stored product.
3
Publicité
