Publicité
Les langues disponibles
Les langues disponibles
If parts seem to be missing or damaged, contact your
supplier immediately.
3.2
Installation
The fan can be placed either on the floor or on a frame.
For mounting on a frame the dimensions and the weight
of the fan should be taken into consideration.
•
Place the fan in such a way, that it remains easy
accessible for maintenance works.
•
Subsequently connect the ductwork. Make sure that
the ductwork is supported well and that the flexible
adapters do not touch any other part of the
installation.
•
Finally check that the complete extraction system is
airtight.
3.3
Mounting the mains cord
.
WARNING
The mains cord must be mounted in accordance
with local regulations. This is strictly reserved to
skilled and authorised service engineers.
3.4
Electric connection
•
Connect the motor as indicated on the motor plate
(star or delta).
•
Subsequently follow the instructions on the
connection box of the motor.
The fan can be connected to the mains using a thermal
relay or a frequency controller.
If the fan is connected to a frequency controller, this
must be done in accordance with the corresponding
manual. Set the current limit in conformance with the
specifications indicated on the type plate of the
electromotor.
After connection always check the direction of rotation of
the motor. For this purpose an arrow has been placed on
the extraction fan indicating the prescribed direction of
rotation.
.
WARNING
Be careful with moving parts. Keep away from
the suction and/or outlet opening.
4
TROUBLESHOOTING
Problem
Possible cause
Motor does
No mains voltage.
not start.
Mains cord
defective.
Loose contacts.
Thermal relay (NTR)
defective.
Motor makes
Motor uses 2
a humming
phases.
sound, but
does not
function.
0507060100/281013/B FAN-42 | SF 4200
Solution
Check the mains
voltage.
Repair or replace
the mains cord.
Repair the contacts.
Repair or replace
the NTR.
Repair the phase
connection.
Problem
Possible cause
Motor stops
Thermal relay (NTR)
auto-
activated.
matically.
Frequency
controller stops on
PTC.
Inverted direction of
rotation of the
motor.
Motor defective.
Extraction
Inverted direction of
capacity
rotation of the
insufficient.
motor.
Fan dirty.
False air is being
sucked.
Vibrations in
Imbalance in the
the
fan.
extraction
fan.
CE DECLARATION
CE Declaration of Conformity for machinery
We, Plymovent Manufacturing B.V., Wezelkoog 11, 1822
BL Alkmaar, the Netherlands, herewith declare, on our
own responsibility, that the products:
•
FAN-42/RD | FAN-42/LG | SF 4200/RD | SF 4200 LG
which this declaration refers to, are in accordance with
the conditions of the following Directives:
•
Machine Directive 2006/42 EC
•
LVD 2006/95 EC
•
ErP Directive 2009/125 EC
An installation is defined as a combination of several finished
products or components that are assembled by an installer at a
given place. The various parts of the installation are intended to
operate together in a particular environment and to perform a
specific task. The entire installation must comply with the
relevant directives and standards. The assembly instructions
given by the manufacturer, as well as the whole method of
installation, must be in accordance with good engineering
practices within the context of installations, as well as installation
rules. Considering the above, the installer will be responsible for
completing the installation and issuing the final CE Declaration of
Conformity.
Alkmaar, 1st November 2013
Ir. F. Coehoorn
Vice President Research & Development
Solution
Let the motor cool
down for some
time.
Let the motor cool
down for some
time.
Change the
direction of
rotation.
Replace or repair
the motor.
Change the
direction of
rotation.
Clean the fan.
Check or replace the
sealing.
Clean the fan.
EN - 5
Publicité
