Features - Rigid R4141 Manuel D'utilisation

ELECTRICAL
SPEED AND WIRING
The no-load speed of this product is approximately 3,900
rpm. This speed is not constant and decreases under a load
or with lower voltage. For voltage, the wiring in a shop is as
important as the motor's horsepower rating. A line intended
only for lights cannot properly carry a power tool motor. Wire
that is heavy enough for a short distance will be too light for
a greater distance. A line that can support one power tool
may not be able to support two or three tools.
GROUNDING INSTRUCTIONS
This product must be grounded. In the event of a malfunction
or breakdown, grounding provides a path of least resistance
for electric current to reduce the risk of electric shock.
This product is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The
plug must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.

FEATURES

PRODUCT SPECIFICATIONS
 Input ............................ 120 V, AC Only, 60 Hz, 15 Amps
 No Load Speed .................................3,900 r/min. (RPM)
 Arbor Diameter ........................................................ 1 in.
 Wheel Diameter ..................................................... 14 in.
KNOW yOUR CUT-OFF MACHINE
See Figures 2A - 2B, page 18.
The safe use of this product requires an understanding of
the information on the tool and in this operator's manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
14 in. ABRASIVE WHEEL
A 14 in. abrasive wheel is included with your cut-off machine.
It will cut materials up to 5 in. thick or 8 in. wide, depending
upon the thickness or width of the material and the setting
at which the cut is being made.
ADJUSTABLE FENCE
The fence on your cut-off machine has been provided to
support the material and provide clamping support to the
vise for holding your material securely when making all cuts.
It is an adjustable fence that has been provided to make
your cut-off machine more versatile. It adjusts from 0° to 45°
to the right or left for making angled cuts. The hole pattern
allows it to be moved forward when making cuts in tall or
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
WARNING:
Improper installation of the grounding plug is able
to result in a risk of electric shock. When repair or
replacement of the cord is required, do not con-
nect the grounding wire to either flat blade terminal.
The wire with insulation having an outer surface
that is green with or without yellow stripes is the
grounding wire.
Check with a qualified electrician or service personnel if
the grounding instructions are not completely understood,
or if in doubt as to whether the product is properly grounded.
Repair or replace a damaged or worn cord immediately.
This product is for use on a nominal 120 V circuit and has
a grounding plug similar to the plug illustrated in figure 1,
page 18. Only connect the product to an outlet having the
same configuration as the plug. Do not use an adapter with
this product.
 Fence Angle ..................................... right (45°), left (45°)
 Maximum Cutting Capacities:
Round Pipe ............................... 5 in. outside diameter
Bar Stock .............................................................. 2 in.
thick stock, such as square stock or tube stock. The hole
pattern allows it to be moved back when making cuts in
stock that is thin or wide, such as angle stock.
ADJUSTABLE STOP
In the down (full cut) position, the pivot arm hits an adjust-
able stop on the support bracket.
ARBOR WRENCH
The arbor wrench is found on the underside of the base. Use
wrench when replacing cut-off wheel or when making fence
angular adjustments.
CARRyING HANDLE
This handle is built into the unit to move it from one
location to another. Before attempting to pick up the unit by
the carrying handle always lock the power head in the down
position using the transport chain.
C-CLAMP SURFACE
Two areas on the machine base provide additional space for
using a C-clamp to secure the workpiece.
8 - English