Bigassfans Powerfoil X2.0 Manuel D'installation page 29

Programming the Wall Control
To select a mode, repeatedly press the Mode button until the green Winter Mode LED, red Summer Mode LED, or
yellow Manual LED is illuminated.
Note: If the fan is set to a high speed when switching between modes, there will be a delay before the fan slows
down to the correct speed. Reduce the fan speed before switching modes to shorten the delay.
To program the maximum fan speed for Winter Mode:
1. To select Winter Mode, repeatedly press the Mode
button on the wall controller until the green Winter
Mode LED is illuminated. After selecting Winter Mode,
press and hold the Mode button for three (3) seconds.
The Winter Mode LED will flash.
2. Press the Up and Down arrow buttons to adjust
the fan speed until a breeze can barely be felt. It is
recommended that the speed be reduced from this
point by 5%. The goal is to find the maximum allowable
speed of the fan that does not produce a wind chill
effect or any discomfort.
3. Press the Mode button once to save the Winter Max
Speed setting and to exit programming mode. The
Winter Mode LED will stop flashing and the Maximum
Fan Speed LEDs will show the fan's current speed.
To program the minimum and maximum speed temperatures for Summer Mode:
1. To select Summer Mode, repeatedly press the
Mode button on the wall controller until the red
Summer Mode LED is illuminated. After selecting
Summer Mode, press and hold the Mode button
for three (3) seconds. The Summer Mode LED will
flash.
2. To set the Minimum Speed Temperature, press
the Up and Down arrow buttons to adjust the
minimum speed temperature. Each press of an
arrow button changes the setting in 2.5° F (1.4° C)
increments.
3. Press the Mode button once to save the Summer
Minimum Speed Temperature. The Summer Mode
LED will flash, indicating that the wall control is
ready to accept a Maximum Speed Temperature.
4. To set the Maximum Speed Temperature, press the Up and Down arrow buttons to adjust the maximum speed
temperature. Each press of an arrow button changes the setting in 2.5° F (1.4° C) increments.
5. Press the Mode button once to save the Summer Maximum Speed Temperature. The Summer Mode LED will
stop flashing and the Threshold Temperature LEDs will show the fan's current speed.
To manually adjust the fan speed, select Manual Mode, and then press the Up and Down arrow buttons to adjust
the fan speed between 10% and 100% as desired.
50°F THRESHOLD TEMPERATURE 100°F
WINTER MODE
SUMMER MODE
MANUAL
MODE
AUTOMATIC
DESTRATIFICATION SYSTEM
10% MAXIMUM FAN SPEED
55°F THRESHOLD TEMPERATURE
WINTER MODE
SUMMER MODE
MANUAL
MODE
WWW.BIGASSSOLUTIONS.COM © 2015 DELTA T CORP.
10%
100%
55°F
100°F
Flashing
when in
programming
mode
50°F THRESHOLD TEMPERATURE
Note: Each LED on the Maximum Fan Speed Bar
WINTER MODE
represents a 10% increase or decrease in speed SUMMER MODE
MANUAL
adjustment. When two LEDs are simultaneously
illuminated, the second LED indicates a 5% increase
(e.g., 15%, 25%, 35%, etc.).
DESTRATIFICATION SYSTEM
10% MAXIMUM FAN SPEED
55°F THRESHOLD TEMPERATURE
WINTER MODE
Flashing
when in SUMMER MODE
programming
MANUAL
mode
Note: Each LED on the Threshold Temperature
Bar indicates a 5° F (2.8° C) increase or decrease
in temperature adjustment. When two LEDs are
simultaneously illuminated,
indicates 5° F (2.8° C) (e.g., 62.5° F [16.9° C], 67.5° F
[19.7° C], 72.5° F [22.5° C], etc.).
ALL RIGHTS RESERVED.
AUTOMATIC
DESTRATIFICATION SYSTEM
MAXIMUM FAN SPEED 100%
THRESHOLD TEMPERATURE 100°F
WINTER MODE
SUMMER MODE
MANUAL
MODE
100°F
MODE
AUTOMATIC
85% Speed Temp
Displayed
100%
100°F
MODE
the second
85% Speed
Displayed
5% Speed
Increase
5% Speed
Decrease
AU
DESTRATI
10% MAXI
55°F THRESH
5% Speed
WINTER
Increase
SUMMER
MANUAL
5% Speed
Decrease
LED
25