Output Parameters - CARLO GAVAZZI LD30 BI10BP IO Série Manuel D'instructions

7.2.3. Output Parameters

Parameter Name
Channel 1 (SO1)
Stage Mode 1
Input selector 1
Timer 1 - Mode
Timer 1 - Scale
Timer 1 – Value
Logic function 1
Output Inverter 1
Channel 2 (SO2)
Stage Mode 2
Input selector 2
Timer 2 – Mode
Timer 2 – Scale
Timer 2 – Value
Logic function 2
Output Inverter 2
30
Rev.00 - 01.2020 | LD30 IO-Link manual ENG | © 2020 | CARLO GAVAZZI Industri
Index Dec
Access
(Hex)
64 (0x40)
1 (0x01) R/W
2 (0x02) R/W
3 (0x03) R/W
4 (0x04) R/W
5 (0x05) R/W
7 (0x07) R/W
8 (0x08) R/W
65 (0x41) -
1 (0x01) R/W
2 (0x02) R/W
3 (0x03) R/W
4 (0x04) R/W
5 (0x05) R/W
7 (0x07) R/W
8 (0x08) R/W 1 = Inverted (Normally Closed)
Default value
1 = PNP output
3 = Push-pull output
1 = SSC 1
3 = Quality of run alarm (TA)
4 = External logic input
0 = Disabled timer
3 = T-on/T-off delay
4 = One-shot leading edge
5 = One-shot trailing edge
0 = Milliseconds
0
0 = Direct
0 = Not inverted 0 = Not inverted (Normal Open)
(N.O.) 1 = Inverted (Normal Closed)
-
3 = Push-Pull output
1 = PNP output 4 = Digital logic input (Active high/
5 = Digital logic input (Active low/
6 = Teach-in (Active high)
1 = SSC 1
3 = Quality of run alarm (TA)
4 = External logic input
0 = Disabled timer
3 = T-on/T-off delay
4 = One-shot leading edge
5 = One-shot trailing edge
0 = Milliseconds
0
0 = Direct
0 = Not inverted (Normally Open)
1 = Inverted (Normally Closed)
Data range Data Type
0 = Disabled output
1 = PNP output
UIntegerT
2 = NPN output
0 = Deactivated
1 = SSC 1
2 = SSC 2 UIntegerT
0 = Disabled timer
1 = T-on delay
2 = T-off delay
UIntegerT
0 = Milliseconds
1 = Seconds UIntegerT
2 = Minutes
0 ... 32'767 IntegerT
0 = Direct
1 = AND
2 = OR UIntegerT
3 = XOR
4 = Gated SR-FF
UIntegerT
- -
0 = Disabled output
1 = PNP output
2 = NPN output
UIntegerT
Pull-down)
Pull-up)
0 = Deactivated
1 = SSC 1
2 = SSC 2 UIntegerT
0 = Disabled timer
1 = T-on delay
2 = T-off delay
UIntegerT
0 = Milliseconds
1 = Seconds UIntegerT
2 = Minutes
0 ... 32'767 IntegerT
0 = Direct
1 = AND
2 = OR UIntegerT
3 = XOR
4 = Gated SR-FF
UIntegerT
Length
8 bit
8 bit
8 bit
8 bit
16 bit
8 bit
8 bit
-
8 bit
8 bit
8 bit
8 bit
16 bit
8 bit
8 bit