Publicité
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Before maintenance always switch off tool, ensure
there is no water pressure in tool and hand gun,
disconnect plug from power source, and disconnect
tool from water supply
• Always keep tool and cord clean (especially ventilation
slots S 2)
- do not use water, solvents or polishes
- regularly clean spraying nozzle G using cleaning needle
M 9 (remove spray lance K from hand gun L first)
• Regularly check for worn or damaged components and
have them repaired/replaced when necessary
• Cleaning water filter
- remove water filter E 2 from inlet connector C 2
with long nose pliers
- rinse it clean and put it back (replace it when damaged)
! never use the tool with a damaged water filter
• Storage 0
- store the tool out of reach of children in a location
where the ambient temperature will not exceed 40°C
or drop below 0°C
- do not place other objects on top of the tool
- securely mount storage rail N on the wall with
4 screws (not supplied) and horizontally leveled
- use storage rail N and storage straps P as illustrated
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
TROUBLESHOOTING
• The following listing shows problem symptoms,
possible causes and corrective actions (if these do not
identify and correct the problem, contact your dealer or
service station)
! switch off the tool and disconnect the plug before
investigating the problem
★ Spray is not consistent
- nozzle partly blocked -> clean nozzle
★ Motor does not start or stops suddenly
- power supply socket faulty -> use another socket
- plug not connected -> connect plug
- thermal protection switched off the motor -> let the
tool cool down for 5 minutes
★ Motor is running but spray is poor
- nozzle completely blocked -> clean nozzle
- water filter clogged -> clean water filter
- air in the pump -> ensure that water inlet connector
is securely fitted
- inadequate water supply -> check that water tap is
fully open
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol ! will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this
product is in conformity with the following standards or
standardized documents: EN 60335 in accordance with
the provisions of the directives 2006/95/EC,
2004/108/EC, 2006/42/EC
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
Arno van der Kloot
Vice President
Operations & Engineering
SKIL Europe BV, 4825 BD Breda, NL
26.10.2010
NOISE/VIBRATION
• Measured in accordance with EN 60704-1 the sound
pressure level of this tool is 81 dB(A) and the sound
power level 93 dB(A) (standard deviation: 2.2 dB),
and the vibration < 2.5 m/s² (hand-arm method;
uncertainty K = 1.5 m/s²)
• Measured in accordance with 2000/14/EC
(EN/ISO 5349) the guaranteed sound power level LWA
is lower than 97 dB(A)
• The vibration emission level has been measured in
accordance with a standardised test given in
EN/ISO 5349; it may be used to compare one tool with
another and as a preliminary assessment of exposure to
vibration when using the tool for the applications
mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
significantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
significantly reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns
F
Laveur haute pression
INTRODUCTION
• Cet outil a été conçu pour nettoyer les zones et objets
situés à l'extérieur de la maison, des véhicules et des
bateaux
8
Jan Trommelen
Approval Manager
0760
Publicité
