Publicité
Les langues disponibles
Les langues disponibles
Use the directional buttons to select "Country", then the
left / right directional buttons to select from among user-
defined data or the country pre-selected in the "Select
Parameter" submenu. If "User Defined" has been selected,
the user can enter the desired frequency and select another
BW (number: 6-8). Go to 'Channel' to select a channel.
•
ANALYZE SPECTRUM
Press [EXIT] to leave the current menu.
The above diagram shows the signal strength of a given
channel contained in "Define User Data" or the selected
country (you can change it in the "Check Channel" menu).
Press the left / right button to scroll the range at a normal
speed or press the up / down buttons to scroll quickly.
EN
The current frequency and signal strength are displayed at
the top of the screen.
•
LIST CHANNEL
This feature shows all channels by country.
Press the up / down buttons to navigate and the left / right
buttons to change the page. Then press [OK] to select the
country's list of channels as in the picture below.
•
DEFINE USER DATA
In this menu, you can add, modify and delete channels.
Select the desired submenu item and confirm with [OK]. You
can change the channel name, frequency and bandwidth in
the "Add Channel" and "Modify Channel" submenus.
Data changes will be saved after pressing the [EXIT] button.
In the "Delete Channel" submenu, use the up / down /
right / left buttons to select the channel and press [OK] to
delete it. Press [EXIT] to leave the submenu.
•
SELECT PARAMETER
In this submenu you can enable / disable the 5V output
socket for the terrestrial antenna and select the country.
•
SETUP
In this submenu you can set the buzzer and manage user
data.
Control Buzzer
»
Turn the buzzer sound on or off..
Backup Data
»
Back up data to an external disk via a USB port
Update Data
»
Update satellite data from an external disk via a USB port.
NOTE: only a ".txt" file named "sf560" will be recognized
and must be saved according to the following formula
(there is an empty path at the end).
16
1
2
3
4
5 6 7
8
9
1.
"01" means the information applies to the satellite.
2.
satellite serial number - must come in succession, it
cannot jump from e.g. '01' to '03'.
3.
Satellite name - up to 10 characters. If the satellite
name is "sat01", it must be written as "00000sat01"
4.
Satellite LO frequency.
5.
22 KHz signal status, where "0" = off, "1" = on.
6.
DisEqC1.0 signal status, where "0" = off, "1" = on.
7.
USALS status, where "0" = disabled, "1" = enabled.
8.
Satellite latitude.
9.
Satellite position, where "0" = east, "1" = west
1
2
3
4
5
6
1.
"001" means the information applies to TP
(transponder).
2.
Transponder number - must be consecutive. It
cannot jump e.g. from "001" to "003".
3.
This number indicates which satellite the transponder
applies to.
4.
Transponder frequency.
5.
Transponder data transmission speed.
6.
Polarization: "0" = H (horizontal), "1" = V (vertical).
3.3.2 SOFTWARE UPDATE
You can update the device software from a disk via a USB
port. To update the software, connect the disk via USB,
press and hold the [MENU] button, then connect the device
to the power supply until the following message appears
on the display:
Then press the [OK] button and the update will start. When
the software update is completed, the device (system) will
restart.
NOTE: do not disconnect the device from the power supply
during the update!
3.4. CLEANING AND MAINTENANCE
a)
Unplug the mains plug and allow the device to cool
completely before each cleaning, adjustment or
replacement of accessories, or if the device is not
being used.
b)
Use only non-corrosive cleaners to clean the surface.
c)
After cleaning the device, all parts should be dried
completely before using it again.
d)
Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
e)
Do not spray the device with a water jet or submerge
it in water.
f)
Do not allow water to get inside the device through
vents in the housing of the device.
g)
Use a soft cloth for cleaning.
h)
Do not leave the battery in the device if it will not be
used for a longer period of time.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used
to construct the device can be recycled in accordance
with their markings. By choosing to recycle you are
making a significant contribution to the protection of our
environment.
Contact local authorities for information on your local
recycling facility.
17
EN
Publicité
