ACTEON Equipment SATELEC Mini LED III Supercharged Manuel D'utilisation page 7

MLED III Supercharged U2
Any fluctuation of the voltage of the ac power supply or
electromagnetic field, noncompliant with the
applicable limits, may affect the unit's operation.
The device is intented to be connected to a separate
power supply (FRIWO FW7660M/12), which is seen as
part of the device.
The plug of the power supply is intented to serve as
disconnected device, the socket-outlet shall be
installed near the equipment and shall be easily
accessible.
Unit operation
Do not use the unit if it appears to be damaged or
defective.
Do not use the unit if the light guide is damaged (injury
hazard...).
Before each use, check that light intensity is compliant
(see section 3.1 TECHNICAL DESCRIPTION) using the
power verification window on the charging base.
When handling the AC power adapter and/or the battery
disconnected from the handpiece, avoid contact with
the patients or other persons.
Do not touch the accessible battery and charging base
connectors (bump contacts).
To disconnect the ac power supply adapter, grip the AC
adapter plug and hold the wall socket.
During dental care, the Mini LED SuperCharged must not
be connected to its charging base.
In the event that the unit is not in use or stored, or in
the case of a prolonged absence, disconnect the AC
adapter from the ac power supply and remove the
battery from the body of the unit to protect it from a
slow and detrimental discharge.
Do not exert excessive pressure on the unit's LCD
screen.
Do not change the battery during use.
Do not short-circuit the battery.
Do not short circuit the charging bump contacts on the
charging base.
Do not incinerate the battery (risk of explosion).
Environment
Do not immerse and do not use outside.
Do not place the unit close to a heat source.
The use of solvents, detergents or flammable
substances can result in damage or even short-circuits.
Ensure that the power cord connecting the AC adapter
to the charging base does not prevent persons from
moving freely.
The unit must be stored in its original packaging, in an
appropriate place, without danger for persons.
V5:Mise en page 1 22/02/2010
For unit transportation, unscrew the battery and
protect the light guide from any unexpected shocks.
Any condensation inside electrical equipment can be
dangerous.
If the lamp must be transported from a cold place to a
warm place, it must not be used immediately, but only
after reaching the ambient temperature.
Never insert or try to insert metallic objects into the
equipment to avoid an electric shock or short-circuit
hazard.
The unit is not designed for operation in the presence of
anesthetic gas or any other flammable gas.
Do not expose the unit to water mist or water splashing.
The unit is not designed for operation close to ionizing
radiation.
Maintenance
Before and after each use, it is essential that the unit
be disinfected with the products recommended by
SATELEC.
Before each use, it is essential that a cleaned and
disinfected rigid protection shield be used.
Before each intervention, it is essential that a cleaned,
disinfected and sterilized light guide be used.
Before each intervention, check the integrity of the unit
and its accessories.
Accessories
Do not use accessories other than those supplied by
SATELEC.
The manufacturer refuses to accept any responsibility if
damaged parts or accessories are not replaced
exclusively by those supplied by the manufacturer. In
particular, the use of light guides, ac adapters or
batteries other than those supplied by the manufacturer
may be dangerous for the patient and the user.
Repair
Do not perform equipment repairs or modifications
without the prior authorization of SATELEC.
In the event of an anomaly, immediately disconnect the
unit's base and ensure that nobody can use the lamp
before verification by the manufacturer or the supplier.
This anomaly may be due to noncompliance with safety
rules or because of technical damage to the unit.
In the event of an anomaly, contact the supplier of the
unit rather than just any repairer, which may return
your unit in a hazardous state for both you and your
patients.
www.acteongroup.com
Email: satelec@acteongroup.com
7
12:47 Page 7