Maintenance And Service; Maintenance And Cleaning - Bosch GSS 23 AE Professional Notice Originale

OBJ_BUCH-80-003.book Page 14 Wednesday, January 30, 2013 9:13 AM
14 | English
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate
of material removal, different sanding sheets are available:
For the working of all wooden
materials
For coarse-sanding, e. g. of
rough, unplaned beams and
boards
For face sanding and planing
small irregularities
For finish and fine sanding of
hard woods
For the working of
paint/enamel coats or primers
and fillers
For sanding off paint
For sanding primer
For final sanding of primers
before coating
Replacing the Sanding Plate (see figure F)
The sanding plate 6 can be replaced, if required.
Unscrew the 4 screws 11 completely and remove the sanding
plate 6. Attach the new sanding plate 6 and tighten the screws
again.
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To start the machine, press the On/Off switch 2 and keep it
pressed.
To lock the pressed On/Off switch 2, press the lock-on button
3.
To switch off the machine, release the On/Off switch 2 or
when it is locked with the lock-on button 3, briefly press the
On/Off switch 2 and then release it.
To save energy, only switch the power tool on when using it.
Preselecting the Orbital Stroke Rate
With the thumbwheel for preselection of the orbital stroke
rate 1, you can preselect the required orbital stroke rate, even
during operation.
The required stroke rate depends on the material and the
working conditions and can be determined through practical
testing.
2 609 141 028 | (30.1.13)
Working Advice
 Wait until the machine has come to a standstill before
The removal capacity during sanding is mainly determined by
Grain size
the selection of the sanding sheet as well as the preselected
40—240
orbital stroke rate.
Only flawless sanding sheets achieve good sanding capacity
and extend the service life of the machine.
Pay attention to apply uniform sanding pressure; this increas-
es the working life of the sanding sheets.
coarse 40, 60
Intensifiying the sanding pressure does not lead to an in-
crease of the sanding capacity, but to increased wear of the
machine and the sanding sheet.
medium 80, 100, 120
A sanding sheet that has been used for metal should not be
used for other materials.
fine 180, 240
Use only original Bosch sanding accessories.
40—320

Maintenance and Service

Maintenance and Cleaning

coarse 40, 60
 Before any work on the machine itself, pull the mains
medium 80, 100, 120
 For safe and proper working, always keep the machine
fine 180, 240, 320
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: (0844) 7360109
Fax: (0844) 7360146
E-Mail: boschservicecentre@bosch.com
placing it down.
plug.
and ventilation slots clean.
Bosch Power Tools