Jonsered LM2148CMD Manuel De L'utilisateur page 10

Oil
1. Check oil level periodically and after every five
hours of operation.
2. Add oil as necessary to keep the level to the FULL
mark on the dipstick.
3. Use a good quality SAE 30 four stroke oil.
4. To fill with oil:-
a) Remove oil filler cap. (D1)
b) Fill to the FULL mark on the dipstick. (D2)
5. Change the oil after the first five hours operation
and thereafter every 25 working hours.
6. Always change the oil while the engine is warm -
but not hot - never attempt any maintenance on a
hot engine.
Please Note:- When starting the engine for the first
time, fill with oil and petrol as described above in the Oil
and Petrol section.
Priming is usually unnecessary when restarting a warm
engine. However, cool weather may require priming to
be repeated.
Starting the engine for the first time
1. Advance engine speed control to FAST '+' as
described in the Use - starting and stopping
section.
G1-a - engine speed control
G3-a - recoil starter
Starting & Stopping LM2148CMD
Starting
1. Connect the spark plug lead.
2. Move the Engine Speed Control to the FAST '+'
position before starting. (G1)
3. Pull the operator presence control (OPC) to release
the brake on the engine and the blade.(G2)
4. Pull the recoil starter fully towards you until you feel the
full resistance, return the handle slowly then pull the
handle firmly towards you to its full extent. (G3)
5. After the engine has started, allow to run for 30
seconds before commencing to use.
Engaging the Drive
1. Forward drive is engaged and disengaged with the
Powerdrive lever at the top of the handle (G4).
2. Releasing the Powerdrive Lever stops the forward
drive automatically.
Stopping
1. Release the powerdrive lever.
2. Release the OPC lever.
How to Mow
1. Always use the correct mowing position (J1).
2. Start mowing from the outside edge of the lawn,
mowing in strips in alternate directions (K2).
3. Mow twice a week in the growing season, your
lawn will suffer if more that one third of its length is
cut at one time and this may also result in poor
collection.
ENGLISH - 3
Engine Notes
Starting - Priming the Engine
Use - Starting and Stopping
Use - Mowing
Petrol
1. Use fresh regular grade lead free petrol.
2. Do not fill the fuel tank when the engine is hot.
3. Do not fill the fuel tank while smoking.
4. Do not fill the fuel tank while the engine is running.
5. To avoid introducing dirt into the fuel system, wipe
all grass and dirt from the petrol filler cap before
unscrewing it. (E1)
6. It is recommended that you fill the tank through a
funnel with a filter. (E2)
7. Wipe away spillages before starting.
Please Note :- move the product away from the fuelling
area before starting
2. Push primer bulb (F) firmly five times
3. Follow instructions in the Use - starting and
stopping section.
4. If engine fails to start after three pulls of the pull
cord, push primer bulb three times and repeat step
3.
Starting engine thereafter
1. Move engine speed control to FAST '+' position and
push primer bulb firmly three times before starting
engine. (if engine stopped because it ran out of fuel,
refuel engine - push primer bulb three times.)
Starting & Stopping LM2148CMDE
Starting
1. Follow steps 1-3 for the LM2148CMD
2. Turn the key and hold until the engine starts (H).
The key will return to the original position when
released.
3. If the engine fails to start when you turn the key
your battery may need charging.
Engaging the Drive - See LM2148CMD
Stopping - See LM2148CMD
Please note:- Your LM2148CMDE can be started
manually by following steps 1-5 in
Starting & Stopping LM2148CMD
Key Start Only - During mowing, your engine will
recharge the battery.
Please Note:-
Do not overload your Lawnmower
When mowing in long thick grass a first cut with the
cutting height adjusted to its highest setting, see
Cutting Height, will help reduce engine overload and
will help prevent damage to your lawnmower.
Cutting Height Adjustment
1. The height of cut is altered by pulling the
adjustment lever away from the location slots and
moving to the selected position (K3).