Safety Precautions - Sammic TR-250 Mode D'emploi

the appliance for a few seconds.
Complete Cleaning Procedure (model TR-
250)
The shaft (5) and the blade must be washed
with water and a general-purpose
detergent.
The motor unit (4) must be cleaned with a
damp cloth. Under no circumstances shall
water enter the motor unit. If necessary,
dry the motor unit.
Once cleaned, place the appliance on the
wall mount.
Complete Cleaning Procedure (models
350 and 550)
When you have finished with the appliance,
detach the foot.
Neither the blender (2) or beater (3) nor the
gear attachment for the stirrer may be
completely immersed in water.
The shaft and the blade must be washed
with water and a general-purpose
detergent.
The motor unit (1) must be cleaned with a
damp cloth. Under no circumstances shall
water enter the motor unit. If necessary,
dry the motor unit.
Once cleaned, place the feet and the motor
unit in the wall mount.
Cleaning Procedure for stirrers
To clean the stirrers, first remove the gear
attachment from the appliance body. Then,
pull the stirrers out of the gear attachment.
Prepare a soapy solution, by mixing four
spoonfuls of a general-purpose cleaner per
litre of water.
With a soft cloth wetted with the soapy
solution, clear any food remains off the
stirrers. Let the stirrers soak in the soapy
solution for at least 30 minutes. Rinse the
stirrers with water, to eliminate any soap
residues.
W
ARNING
Do not use hot water for cleaning the
stirrers.
After washing the stirrers, allow them to
dry at room temperature. Fitting the
stirrers is done in reverse order of their
removal.
IMPORTANT ADDITIONAL INFORMATION
The airborne noise emitted
appliance, as measured on a type appliance
at a distance of 1m, is less than 75dB(A).
Technical Data
A
LL THE MODELS
- The constructional materials of the
appliance have been
conformity with the applicable food
standards currently in force.
- The machine features a drive safety
device. In order to start the appliance, it is
essential that two buttons are pushed
simultaneously.
- All appliances are supplied complete with
a wall mount for practical storage in the
kitchen.
M 350 550
ODELS AND
- The motor unit (1) has three sealed
control push-buttons.
- The electronic control prevents the
appliance from restarting in the event of a
power failure or if the appliance has been
unplugged.
- A built-in thermal protection would stop
the motor in case of overload.
- The Mixing or beating foot is detachable
to ensure thorough cleaning.

SAFETY PRECAUTIONS

- Always unplug the appliance before any
cleaning, inspection or repair of the same.
- Blades are sharp. Be careful when
cleaning them.
- Never operate the appliance on no load,
outside a vessel. The foot must be
immersed to a maximum depth of 2/3 its
total length. Maximum
inclination of the appliance shall not
exceed 30º (see Figure 6).
- Always work with a stable vessel.
- To prevent splashes, plunge the foot into
the vessel before switching it on, and take
it out of the vessel only when the
appliance has stopped completely.
- Never put your hand or any utensil in a
vessel with a working appliance, in order
to avoid personal injury or material
damages.
- Take care that water does not flow into
the motor unit.
TROUBLESHOOTING
by the The appliance will not start
- Check whether it is plugged.
- Verify that the power supply specification
is OK and current is fed to the outlet.
- If you have model TR-250, make sure you
push both the ON/OFF switch (6) and
safety switch (7) simultaneously. Refer to
Figure 3.
selected in - If your model is 350 or 550, make sure
you push both the ON/OFF switch (9) and
the safety switch (11). See Figure 4 or 5.
- If the problem persists, contact the
technical assistance service of SAMMIC
S.A.
The appliance stops while working
- In the event of overheating of the
appliance, unplug it and wait for a few
minutes until the motor has cooled down
and the thermal probe has reset (models
350 and 550 only).
- Otherwise, check the power supply to the
outlet.
- If the problem persists, contact the
technical assistance service of SAMMIC
S.A.
working
5
ENGLISH