Ryobi EAG-8512R Manuel D'utilisation page 6

GB
FR DE ES
SAFETY INSTRUCTIONS FOR ALL
OPERATIONS
When wheel is binding or when interrupting a cut
Q
for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes
to a complete stop. Never attempt to remove the
cut-off wheel from the cut while the wheel is in
motion otherwise kickback may occur. Investigate
and take corrective action to eliminate the cause of
wheel binding.
Do not restart the cutting operation in the
Q
workpiece. Let the wheel reach full speed and
carefully reenter the cut. The wheel may bind, walk
up or kickback if the power tool is restarted in the
workpiece.
Support panels or any oversized workpiece to
Q
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near
the line of cut and near the edge of the workpiece on
both sides of the wheel.
Use extra caution when making a "pocket
Q
cut" into existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
Additional safety instructions for sanding operations
NOTE: If sanding operation is not recommended by the
manufacturer, this section may be omitted.
Safety Warnings Specific for Sanding Operations:
Do not use excessively oversized sanding disc
Q
paper. Follow manufacturers recommendations,
when selecting sanding paper. Larger sanding
paper extending beyond the sanding pad presents a
laceration hazard and may cause snagging, tearing of
the disc or kickback.
Additional safety instructions for polishing
operations
NOTE: If polishing operation is not recommended by the
manufacturer, this section may be omitted.
Safety Warnings Specific for Polishing Operations:
Do not allow any loose portion of the polishing
Q
bonnet or its attachment strings to spin freely.
Tuck away or trim any loose attachment strings.
Loose and spinning attachment strings can entangle
your fingers or snag on the workpiece.
IT NL PT DK SE FI NO RU PL CZ
English
Additional safety instructions for wire brushing
operations
NOTE: If wire brushing operation is not recommended by
the manufacturer, this section may be omitted.
Safety Warnings Specific for Wire Brushing
Operations:
Be aware that wire bristles are thrown by the
Q
brush even during ordinary operation. Do not
overstress the wires by applying excessive load
to the brush. The wire bristles can easily penetrate
light clothing and/or skin.
If the use of a guard is recommended for wire
Q
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel or
brush may expand in diameter due to work load and
centrifugal forces.
ANGLE GRINDER SAFETY PRECAUTIONS
Check that the speed marked on the grinding wheel is
Q
equal to or greater than the rated speed of the tool.
Ensure that the dimensions of the grinding wheel are
Q
compatible with the tool and that the wheel fits the
spindle.
Grinding wheels must be stored in a dry place.
Q
Do not store objects on top of the grinding wheels.
Q
Grinding wheels must not be used for any operation
Q
other than grinding.
Grinding wheels must be stored and handled with care
Q
in accordance with the manufacturer's instruction.
Inspect the grinding wheel before use to ensure that it is
Q
not chipped or cracked. Chips or cracks can cause the
wheels to shatter, resulting in possible serious injury.
Ensure that the wheel is fitted in accordance with this
Q
manual.
Ensure that the grinding wheel is correctly mounted
Q
and tightened before use and run the tool at no-
load speed for 30 seconds in a safe position. Stop
immediately if there is considerable vibration or if
other defects are detected. If this condition occurs,
check the tool to determine the cause.
Do not use separate reducing bushings or adapters to
Q
adapt large hole grinding wheels.
Check that the work piece is properly supported.
Q
Use only grinding wheels approved by RYOBI.
Q
Ensure that sparks resulting from use do not create
Q
a hazard e.g. do not hit people, or ignite flammable
substances.
3
HU RO LV LT EE HR SI SK GR TR