Ansonic LP 12 Livret D'instructions page 15

7.4 CLEANING OF THE DISHWASHER'S EXTERNAL SURFACES
The dishwasher's surfaces (made of metal, and in the front of plastic) must be cleaned periodically.
Use a clean and soft piece of fabric. Never use acids or abrasive detergents.
If you don't use the appliance for long periods of time
If the dishwasher is not being used for extended periods of time, you should proceed as follows:
• run the pre-wash programme twice
• remove the electric plug from the outlet
• disconnect the water supply tube
• leave the door slightly open to avoid the formation of bad odours.
7.5 TABLE OF ERROR CODES - "basic version"
N.B.: Anomalies are signalled in the following way:
All the LEDs remain on, while the LED corresponding to the type of error flashes.
Error
When this occurs
LED 1 During the water cycle
(the program stops)
LED 2
At the end
of the cycle
At the end
LED 5
of the cycle
At the end
LED 4
of the cycle
N.B.: Upon contacting the authorised technical assistance centre always communicate the type of error encountered.
7.5 TABLE OF ERROR CODES - "intermediate version"
N.B.: Anomalies are signalled in the following way:
A) All the LEDs remain on, while the LED corresponding to the type of error flashes.
B) A continuous beep sounds until the programme with the error is reset.
Error When this occurs
LED 1 During the water cycle
(the program stops)
LED 2
At the end
of the cycle
At the end
LED 5
of the cycle
At the end
LED 4
of the cycle
At the end
LED 1-2
of the cycle
At the end
LED 1-2
of the cycle
N.B.: Upon contacting the authorised technical assistance centre always communicate the type of error encountered.
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
14
1 2 3 4 5 6 7 8 9 0
GB
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
Checks to carry out
- Tap closed
- Filter of loading tube blocked
- Drainage tube flat
- Drainage tube broken
- Water supply tube bent
- Insufficient water pressure
- Repeat the washing cycle
- The drainage tube is bent
- The siphon is blocked
- The drainage pump is blocked
- The filter grills are blocked
- A pot is placed up side down
Checks to carry out
- Tap closed
- Filter of loading tube blocked
- Drainage tube flat
- Drainage tube broken
- Water supply tube bent
- Insufficient water pressure
- Repeat the washing cycle
- The drainage tube is bent
- The siphon is blocked
- The drainage pump is blocked
- The filter grills are blocked
- A pot is placed up side down
- The filter grills are blocked
- A pot is placed up side down
- Repeat the washing cycle
Action to be taken
- Reset the dishwasher
- Check
- Reset the dishwasher
- Call the authorised assistance centre
- Reset the dishwasher
- Verify the water pressure
- If the same problem reoccurs, contact the authorised
technical assistance centre immediately communica-
ting to them the type of error that is shown.
- Check
- Check
- Call the authorised assistance centre
- Clean the filter grills
- Check at the end of the cycle, position the pots
correctly during the next wash
Action to be taken
- Reset the dishwasher
- Check
- Reset the dishwasher
- Call the authorised assistance centre
- Reset the dishwasher
- Verify the water pressure
- If the same problem reoccurs, contact the authorised
technical assistance centre immediately communica-
ting to them the type of error that is shown.
- Check
- Check
- Call the authorised assistance centre
- Clean the filter grills
- Check at the end of the cycle, position the pots
correctly during the next wash
- Clean the filter grills
- Check at the end of the cycle, position the pots
correctly during the next wash
- If the same problem reoccurs, contact the authorised
technical assistance centre immediately communica-
ting to them the type of error that is shown.