Troubleshooting Guide - Magnavox 37MD350B Manuel De L'utilisateur

Masquer les pouces Voir aussi pour 37MD350B:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

T T
ROUBLESHOOTING
 Troubleshooting Guide
If the unit does not perform properly when operated as instructed in this manual,
check the following chart and all connections once before calling for service.
g
Symptom
No power
Control button does not work.
Power is ON but no screen
image.
No picture or sound
T
V
No color
Adjusted ''PICTURE" or ''SOUND"
is not effective every time turn
on the unit.
Sound OK, picture poor
Picture OK, sound poor
You see a distorted picture or
hear an unusual sound.
Ghosts, lines or streaks in
picture
You see "noise" or "trash" on the
screen.
Different color marks on the TV
screen
52
52
EN
g
Remedy
• Make sure the AC power cord is plugged in.
• Make sure that the AC outlet supplies the proper voltage, plug another electrical
appliance into the AC outlet.
• If a power failure occurs, unplug the AC power cord for 1 minute to allow the unit
to reset itself.
• Press only one button at a time. Do NOT press more than one buttons at the same
time.
• Check whether the connection of the antenna, cable receiver or satellite box is
connected correctly.
• Check whether all the cables to the unit are connected to the correct output jack
of your device like BD/DVD recorder.
• Make sure that the selected input mode is connected to the working input jack.
• Check if your computer is NOT in sleep mode when the input mode of this unit is
in PC mode. Tap any key on the keyboard to wake up your computer.
• Check if the power is on.
• Check if the right input mode is selected.
• Check whether all the cables to the unit are connected to the correct output jack
of your device like BD/DVD recorder.
• View other TV channels. The problem might be limited to the broadcasting station.
• Turn off the unit and wait for about 1 minute, then turn on the unit again.
• Check whether the connection of the antenna, cable receiver or satellite box is
connected correctly.
• Make sure that the selected input mode is connected to the working input jack.
• Check if your computer is NOT in sleep mode when the input mode of this unit is
in PC mode. Tap any key on the keyboard to wake up your computer.
• Make sure that the sound is not muted. Press [MUTE] so that the volume bar and
current volume level will appear on the TV screen.
• Make sure that the volume is NOT set to "0" or "Mute". If so, use [VOL
adjust the desired volume.
• View other TV channels. The problem might be limited to the broadcasting station.
• Adjust "Color" in the main menu.
• You must set "Home" in "Location". Refer to page 35.
Otherwise, the settings you adjusted will not be memorized after you turn off the
unit.
• Electrical interference from nearby appliances may affect picture quality.
• Adjust "Contrast" and "Brightness" in the main menu.
• View other TV channels. The problem might be limited to the broadcasting station.
• For the best picture quality, watch "high definition" wide screen programs.
If the HD content is not available, watch "standard definition" programs instead.
• View other TV channels. The problem might be limited to the broadcasting station.
• Check if the audio cable is connected in correctly.
• You may be getting interference from electrical appliances, automobiles,
motorcycles or fl uorescent lights.
• Try moving the unit to another location to see if this is the cause of the problem.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
• When the capabilities of the unit exceed the capabilities of the digital
broadcasting, the signal will be increased to match the capabilities of the display
of the unit. This may cause noise or trash.
• View other TV channels. The problem might be limited to the broadcasting station.
g
+
-
/
] to

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

32md350b

Table des Matières