About Remaining Battery Indicator; How To Recharge Usb Device; Maintenance And Inspection; Filter Maintenance - HIKOKI RP 3608DB Mode D'emploi

English
This Product
Turn ON the power
switch (Fig. 5)
Begin search
(Select "Auto" with the
Auto/Manual switch)
(Fig. 13)
Connection (Pairing)
complete* (Fig. 14)
* Requires 1 to 3 seconds (time may vary depending
on distance and obstructions) for both units to search
(fl ashing lamps) and establish a connection (lamps lit).
NOTE
○ No more than two units can be paired simultaneously.
○ It will take approximately 0.5 seconds for the product to
activate after switching ON the electric power tool.
Also, when you switch OFF, the product will stop a few
seconds later to complete vacuuming the waste in the
hose.
○ While the electric power tool is searching (fl ashing
display lamp), drawing the electric power tool's switch
will activate the cleaner's motor.
Upon completion of the connection (lamp lit), the
product will be activated.
The cleaner's motor will not start during a search.
○ When pairing multiple sets, pair one set at a time.
○ While in Auto mode, the product will be automatically
powered OFF if there is no operation for two hours.
○ The eff ective range for wireless linking is approximately
10 m.
This range may be shortened by obstructions between
this product and the electric power tool.
○ When disconnected, this product will return to search
status.
Turn Auto OFF
Switching Auto OFF using the product
Pressing the Auto/Manual switch of the product will
activate Manual mode and break the connection.
When the connection is broken, the Auto mode of the
electric power tool will be automatically switch OFF.
This Product
Auto OFF (Manual mode)
(Fig. 17)
* Auto mode can be switched OFF by switching off the
product's power.
Switching Auto OFF using the electric power tool
A long press of the wireless link switch of the electric power
tool will switch to Manual mode, cutting the connection.
When the connection is cut, the electric power tool will
automatically begin searching.
This Product
Connection OFF
(Searching) (Fig. 19)
Bluetooth Compatible
Product
Draw the switch once
(Fig. 12)
Begin search
(Press the wireless link
switch) (Fig. 15)
Connection (Pairing)
complete* (Fig. 16)
Bluetooth Compatible
Product
Connection OFF (Auto OFF
(Manual mode)) (Fig. 18)
Bluetooth Compatible
Product
Auto OFF (Manual mode)
(Fig. 20)
ABOUT REMAINING BATTERY
INDICATOR
Remaining battery power can be verifi ed with either the
battery or with the cleaner itself. (Fig. 28)
NOTE
○ The reading for the remaining battery power may diff er
on the battery from that of the cleaner.
○ Use the remaining battery power as a guideline since
the readings may somewhat diff er due to surrounding
temperature or battery feature.
○ Verify the cleaner's remaining battery power when the
product is powered OFF.

HOW TO RECHARGE USB DEVICE

(UC18YSL3)
(1) Select a charging method
○ Charging a USB device from a electrical outlet
(Fig. 29-a)
○ Charging a USB device and battery from a electrical
outlet (Fig. 29-b)
(2) How to recharge USB device (Fig. 30)
(3) When charging of USB device is completed (Fig. 31)

MAINTENANCE AND INSPECTION

WARNING
○ For inspection and maintenance, be sure to turn off the
vacuum switch and disconnect the battery.
○ Do not work with wet hands. May cause electric shock
or injuries.

1. Filter maintenance

To maintain the product's suction power, frequently
remove any attached dust from the dust fi lter, prefi lter,
cloth fi lter or fi lter damper. (Fig. 9)
(1) Gently tap by hand to remove dust from the prefi lter,
cloth fi lter and fi lter damper. Using compressed air will
make the task easier.
(2) For the dust fi lter, use a brush or compressed air to
clean.
Regularly wash off any dust from the dust fi lter with
water once every month or two months.
After washing the fi lter, suffi ciently dry it in the shade
and use the fi lter once again.
NOTE
○ Even if the prefi lter is clogged, gently tap it to clear
away dust.
Scrubbing it with a brush or other tool will only shorten
its lifespan.
○ Do not infl ict impact on the dust fi lter.
Doing so may crack the resin portion of the fi lter.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
16