Specific Safety Instructions; Technical Data - REMS Cento Instructions De Service

eng
D) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source before making any adjust-
ments, changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to ope-
rate the power tool. Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tools operation. If damaged, have the power tool repaired by a
qualified expert or by an authorised REMS after-sales service facility
before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Secure the workpiece. Use clamps or a vice to hold the workpiece. This
is safer than holding it with your hand, and also it frees both hands to ope-
rate the equipment.
h) Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for the particular type
of power tool, taking into account the working conditions and the work
to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation. All unauthorised modifica-
tions to the power tool are prohibited for safety reasons.
E) Battery tool use and care
a) Ensure the switch is in the off position before inserting battery pack.
Inserting the battery pack into power tools that have the switch on invites
accidents.
b) Recharge only with the charger specified by the manufacturer. A char-
ger that is suitable for one type of battery may create a risk of fire when used
with another battery pack.
c) Use battery tools only with specifically designated battery packs. Use
of any other battery packs may create a risk of injury and fire.
d) When battery pack is not in use, keep it away from other metal objects
like paper clips, coins, keys, nails, screws, or other small metal objects
that can make a connection from one terminal to another. Shorting the
battery terminals may cause bums or a fire.
e) Under abusive conditions, liquid may be ejected from the battery, avoid
contact. If contact accidentally occurs, flush with water. If liquid con-
tacts eyes, additionally seek medical help. Liquid ejected from the
battery may cause irritation or bums.
f) Do not use the battery/charger at battery/charger temperatures or
ambient temperatures of 5°C/40°F or 40°C/105°F.
g) Do not dispose defective batteries in the normal domestic waste. Take
them to an authorised REMS after-sales service facility or to a reputed
waste disposal company.
F) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
b) Comply with maintenance instructions and instructions on tool
replacements.
c) Check mains lead of power tool regularly and have it replaced by a
qualified expert or an authorised REMS after-sales service facility in
case of damage. Check extension cable regularly and replace it when
damaged.

Specific Safety Instructions

Do not overload the pipe cutting machine. Do not use damaged cutting
•
wheels. Use moderate feeding pressure.
Caution! Keep hair, clothing and gloves away from the pipe rest when a
•
pipe is rotating in the rollers. Loose clothing, jewellery or long hair could
get caught between the rotating pipe and the rollers.
Do not reach into the rotating cutting wheel.
•
Where necessary use a material support REMS Herkules (Art.No. 120100)
•
on each side to support long pipes and position the pipe and material
support(s) exactly with the pipe support (3) of the pipe cutting machine.

1. Technical Data

1.1. Article numbers
REMS Cento
REMS cutter wheel Cu-INOX
REMS cutter wheel V
REMS cutter wheel St
REMS cutter wheel Cu
Stand
Rollers INOX (set) for stainless steel pipes
Ring spanner SW 27/17
REMS Herkules material rest with 3 legs
REMS Herkules Y material rest with clamp
REMS Jumbo collapsible workbench
1.2. Application Area
Stainless steel pipes, copper pipes,
composite pipes of press-fitting systems
Max. wall thickness of steel pipes, copper pipes
Max. wall thickness of composite pipes
1.3. Speed
Idle speed of cutting wheel
1.4. Electrical Data
230 V 1~; 50-60 Hz; 1200 W; 5.7 A or
110 V 1~; 50-60 Hz; 1200 W; 11.4 A
Fuse (mains) 10 A (B), cut-out S3 20% (AB 2/10 min), insulated, radio
interference suppressed.
1.5. Dimensions
L×W×H:
1.6. Weights
REMS Cento without foot switch
1.7. Noise Data
Workplace-related emission value
1.8. Vibrations
Weighted effective value of the acceleration
2. Commissioning
2.1. Electrical Connection
Pay attention to mains voltage! Before connecting the device, make sure
that the voltage specified on the rating plate matches the mains supply.
2.2. Installation of the Machine
Bolt the pipe cutting machine to a workbench or similar or to the stand
(Fig. 2) (Art.No. 849315) using 4 x M8 screws. Where applicable, lon-
ger pipes should be supported on both sides using REMS Herkules (Fig.
2) (Art.No. 120100).
2.3. Installing (changing) the cutter wheel (2)
Pull out the mains plug! Select a suitable cutting wheel:
REMS cutter wheel Cu-INOX for stainless steel pipes, jacketed
•
steel pipes and copper pipes of the press-fitting systems,
REMS cutter wheel V for multi-layered composite pipes of the
•
pressfitting systems,
REMS cutter wheel St for steel pipes, cast iron pipes (SML), only
•
for machine no. 630000 and onwards,
REMS cutter wheel Cu for copper pressfitting-system pipes.
•
Loosen the hexagonal nuts which fasten the cutting wheel (right-hand
thread) with the size 27 ring spanner provided. Insert (change) the cutting
wheel (2). Make sure that the carrier pins of the drive shaft grip into the
holes of the cutting wheel. Tighten the hexagonal nuts firmly.
Caution: If an unsuitable cutting wheel is used, the wheel will be da-
maged or the pipe will not be cut. Only use original REMS cutting wheels!
eng
845001
845050
845051
845052
845053
849315
845110
849112
120100
120130
120200
Ø 22 –108 mm
2.5 mm
7.5 mm
115 rpm
250×300×250 mm (10"×12"×14")
17.8 kg (39 lbs)
83 dB(A)
2,5 m/s 2