Publicité
Les langues disponibles
Les langues disponibles
ASSEMBLY INSTRUCTIONS.-
1.
Take the unit out of its box and make sure that
all of the pieces are there, Fig.1:
(117)
Handrail.
(H)
Monitor.
(1)
Main body.
(118)
Handrail Handlebar.
(172)
Rear trim cover.
(G)
The adapter.
(151)
Screw M-10x30.
(150)
Screw M-10x80.
(162)
Allen screw M-6x65.
(153)
Allen screw M-8x25.
(158)
Allen screw M-8x55.
(152)
Allen screw M-10x25. 4
(147)
Screw Phillips M-5x15.
(157)
Screw Phillips M-4x15.
(156)
Flat washer M-10.
(154)
Flat washer M-8.
(155)
Grower washer M-10.
(148)
Combination spanner.
(149)
Star driver spanner.
(161)
Allen key 5mm.
(160)
Allen key 6mm.
(159)
Allen key 8mm.
2
. FITTING THE HANDRAIL HANDLEBAR.-
Bring the handrail handlebar (118) up to boss on
the main body (1), Fig.2
Take terminal and, with the help of the cord (20-22)
already inserted inside the handlebar tube, pull it in
through the tube (118) bringing it out trough the
top.
Now slip the handlebar tube over the boss on the
main body (1) in the direction of the arrow, as
shown in Fig.2, making sure not to snag any of the
cables.
Next, take screw (152) along with the spring
washer (155), Fig.2, and secure. Then take screws
(150) along with their spring weashers (155) and
flat washers (156) and secure. Finally, take screws
(151) along with the spring washers (155) and flat
washers (156) and tighten securely, including
those fitted previously.
3. FITTING THE UPPER HANDLE
Take hold of the handrail monitor (117) and bring it
up to the handlebar tube, as shown in Fig.3.
Connect the terminals , sticking up out of the top of
the tube, with terminal
bottom of the monitor (117), Fig.3, and insert the
tube on the monitor into the boss on the main body
(1) in the direction of the arrow, making sure not to
snag any of the cables.
Once you have checked that it works, insert
screws (162) and (158) along with their flat
washers (154), Fig.3.
Then take screws (153), tighten as shown in
Fig.3A.
coming down from the
Line the handlebar up with the machine and
tighten the screws securely.
4.
FITTING THE FRONT TRIM COVER.-
Place the trim cover (172) on the front part of the
machine, Fig.3. Next, take screws (147) and
secure the cover by tightening the screws.
5.
FITTING THE TOP TRIM COVERS.-
Move the top trim covers up to the handlebar tube,
Fig.3. Take screws (157) and screw them on.
6. FITTING THE
Next, connect terminals, sticking out of the handlebar
(117), and terminals, sticking out of the monitor (H),
Fig.4.
Place the monitor (H) on top of the plate on the main
post (69), as shown in Fig.4, making sure not to pinch
the wires.
Use screws (170) to hold the monitor in place, Fig.4.
Place the rear monitor cover with screws.
7.
LEVELLING.-
Once the unit has been placed into its final position
for doing exercise Fig.5, make sure that it sits flat
on the floor and that it is level. This can be
achieved by screwing the adjustable support
blocks (R) up or down, as shown in Fig.6.
8.
MOVEMENT & STORAGE.-
The appliance is equipped with wheels (104)
making it easier to move about. The two wheels at
the front of the appliance make it easy to store the
machine away, as shown in Fig.7.
9.
PULSE MEASUREMENT.-
Your pulse rate is measured by placing both hands
on pulse sensors (132) located on the seat
handgrips or the handlebar, see Fig.8.
NOTE: You can also use the chest band
(OPTIONAL TELEMETRIC PULSE SENSOR) to
measure your heart rate.
The reading from the telemetric pulse rate takes
preference over the pulse sensors (132) located on
the seat handgrips or handlebar.
10.
BATTERY CHARGE.-
Before starting the battery charge, make sure that
the mains voltage is compatible with the AC/DC
adaptor.
Connect the AC/DC adaptor (G) to the mains.
Then, connect the DC terminal to the connector
located at the low end of the chain cover Fig.9.
BH RESERVES THE RIGHT TO MODIFY
THE SPECIFICATIONS OF ITS PRODUCTS
WITHOUT PRIOR NOTICE.
8
SK
sportkoncept
MONITOR.-
LINE
Publicité
