Before Putting The Machine Into Operation - EINHELL TH-MS 2513 T Mode D'emploi D'origine

Anleitung_TH_MS_2513_T_SPK1__ 03.05.13 08:07 Seite 18
GB
Switch the appliance off when it is not in use.
n
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.
3. Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
is not properly guided and maintained.
6. Before putting the machine into
operation
The machine must be set up where it can stand
n
securely, i.e. it should be fastened with 4 screws
to a workbench, a universal base frame or similar.
All the covers and safety devices have to be
n
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
n
freely.
When working with wood that has been
n
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
n
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
n
supply, make sure the data on the rating plate is
the same as that for your mains.
Secure the clamp (37) on the top of the stop rail
n
using the screw.
6.1 Setting up the saw (Fig. 1-4)
Insert the two workpiece support clips (20) in the
n
mounts (13) provided on the side of the tool and
fasten them in place with screws (36).
To prevent the saw from toppling backwards, the
n
additional foot (a) must be pulled out of the
equipment (Fig. 4).
6.2 Converting the combination saw (Fig. 1-8)
The saw has two working positions:
A: Bench circular saw (Fig. 1)
B: Crosscut and miter saw (Fig. 2)
Convert the combination saw can be converted
exactly as described below, otherwise the
components may be damaged.
18
Important: Pull out the mains plug before you
convert the saw.
When it is supplied, the saw will be in mode A (bench
circular saw)
6.2.1 Converting the saw for crosscut mode
First undo the lock nuts (15).
n
Applying slight counterpressure, hold down the
n
saw table (16) and release the locking lever (24)
(move downwards).
Important. The integral resetting springs will
n
automatically lift the equipment. Do not simply let
go of the saw handle (16) but allow the saw
handle to rise slowly, applying slight
counterpressure as it does so.
Retighten the locknut (15).
n
Retighten the locking lever (24).
n
Push the machine head downwards using the
n
handle (2) and pull out the safety pin (23). This
will disconnect the switch (4) for bench mode
from the power supply and connect the switch (3)
for crosscut mode to the voltage supply.
Important. The integral resetting springs will
n
automatically lift the machine head. Do not
simply let go of the handle (2), but allow the
machine head to rise slowly, applying slight
counterpressure as it does so.
Remove the bottom saw blade cover (14).
n
The saw has now been converted for crosscut
n
mode.
6.2.2 Converting the saw for bench mode
Position the machine head vertically and set the
n
turntable (8) to 0°. At this point you can either
carry out the instructions in 6.2.1 in reverse order
or follow the instructions below.
Secure the locking screws (10) and the
n
tightening screw (22).
Place the bottom saw blade cover (14) on the
n
turntable (8), ensuring that the two rear feet on
the cover (14) engage securely behind the stop
rail (7).
Press the release button (1) and lower the
n
machine head using the handle (2) until the
bottom saw blade guard (14) completely covers
the saw blade.
Insert the safety pin (23) to secure the saw in the
n
bottom position. This will reroute the power from
switch (3) to switch (4).
Release the locking lever (24) (move it
n
downwards)
Undo the locking screw (15) and lower the saw
n
bench (16) to the required cutting depth.
Retighten the locknut (15).
n
Re-tighten the locking lever (24).
n
Lowering the saw bench (16) will block the safety
n