Pioneer DEH-P7400MP Manuel D'installation
Masquer les pouces Voir aussi pour DEH-P7400MP:

Publicité

Les langues disponibles

Les langues disponibles

DEH-P7400MP
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Printed in Thailand
Imprimé en Thaïlande
<CRD3527-A/N> UC
<KKNZF/01H00000>
Connecting the Units
<ENGLISH>
Note:
• This unit is for vehicles with a 12-volt battery and
• When this product's source is switched ON, a con-
negative grounding. Before installing it in a recre-
trol signal is output through the blue/white lead.
ational vehicle, truck, or bus, check the battery
Connect to an external power amp's system remote
voltage.
control or the car's Auto-antenna relay control ter-
• To avoid shorts in the electrical system, be sure to
minal (max. 300 mA 12 V DC). If the car features
disconnect the ≠ battery cable before beginning
a glass antenna, connect to the antenna booster
installation.
power supply terminal.
• Refer to the owner's manual for details on con-
• When an external power amp is being used with
necting the power amp and other units, then make
this system, be sure not to connect the blue/white
connections correctly.
lead to the amp's power terminal. Likewise, do not
• Secure the wiring with cable clamps or adhesive
connect the blue/white lead to the power terminal
tape. To protect the wiring, wrap adhesive tape
of the auto-antenna. Such connection could cause
around them where they lie against metal parts.
excessive current drain and malfunction.
• Route and secure all wiring so it cannot touch any
• To avoid short-circuiting, cover the disconnected
moving parts, such as the gear shift, handbrake
lead with insulating tape. Especially, insulate the
and seat rails. Do not route wiring in places that
unused speaker leads without fail. There is a possi-
get hot, such as near the heater outlet. If the insula-
bility of short-circuiting if the leads are not insulat-
tion of the wiring melts or gets torn, there is a dan-
ed.
ger of the wiring short-circuiting to the vehicle
• To prevent incorrect connection, the input side of
body.
the IP-BUS connector is blue, and the output side
• Don't pass the yellow lead through a hole into the
is black. Connect the connectors of the same colors
engine compartment to connect to the battery. This
correctly.
will damage the lead insulation and cause a very
• If this unit is installed in a vehicle that does not
dangerous short.
have an ACC (accessory) position on the ignition
• Do not shorten any leads. If you do, the protection
switch, the red lead of the unit should be connected
circuit may fail to work when it should.
to a terminal coupled with ignition switch ON/OFF
• Never feed power to other equipment by cutting
operations. If this is not done, the vehicle battery
the insulation of the power supply lead of the unit
may be drained when you are away from the vehi-
and tapping into the lead. The current capacity of
cle for several hours. (Fig. 1)
the lead will be exceeded, causing overheating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on this unit.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right ≠ speaker leads are common.
• Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
ACC position
No ACC position
with output and/or impedance values other than
those noted here may result in the speakers catch-
ing fire, emitting smoke, or becoming damaged.
• The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the ground
becomes detached, there is a risk of damage to the
products or fire.
• Cords for this product and those for other products
may be different colors even if they have the same
function. When connecting this product to another
product, refer to the supplied Installation manuals
of both products and connect cords that have the
same function.
Fig. 1

Publicité

Table des Matières
loading

Sommaire des Matières pour Pioneer DEH-P7400MP

  • Page 1 • Route and secure all wiring so it cannot touch any • To avoid short-circuiting, cover the disconnected DEH-P7400MP moving parts, such as the gear shift, handbrake lead with insulating tape. Especially, insulate the and seat rails. Do not route wiring in places that unused speaker leads without fail.
  • Page 2: Connecting The Units

    Connecting the Units <ENGLISH> 7 When not connecting a rear speaker lead to a Subwoofer 7 When using a Subwoofer without using a different amp (sold separately) Front output Front output 16 cm [5/8 in] 16 cm [5/8 in] Power amp (sold separately) Connecting cords with RCA pin plugs...
  • Page 3: Din Front/Rear-Mount

    Installation <ENGLISH> Note: Removing the Unit (Fig. 6) (Fig. 7) DIN Rear-mount Fixing the Front Panel • Before finally installing the unit, connect the • If installation angle exceeds 60° from horizontal, wiring temporarily, making sure it is all connected the unit might not give its optimum performance.
  • Page 4: Raccordements Des Appareils

    Raccordements des appareils <FRANÇAIS> Remarque: • Cet appareil est destiné aux véhicules avec une bat- • Quand la source de ce produit est positionnée sur terie de 12 V, avec pôle négatif à la masse. Avant de ON, un signal de commande est sorti par le fil l’installer dans un véhicule de loisir, un camion ou bleu/blanc.
  • Page 5 Raccordements des appareils <FRANÇAIS> 7 Lorsque l’on ne connecte pas de câble de liaison au haut-parleur d’extrêmes graves 7 Lors de l’utilisation d’un haut-parleur d’extrêmes graves sans amplificateur extérieur (vendu séparément) Sortie avant Sortie avant 16 cm Amplificateur de 16 cm puissance (vendu séparément) Câbles de liaison munis...
  • Page 6: Fixation De La Face Avant

    Installation <FRANÇAIS> Remarque: Dépose de l’unite (Fig. 6) (Fig. 7) Montage DIN arrière Fixation de la face avant • Avant de finaliser l’installation de l’appareil, con- • L’angle de l’installation, ne doit pas dépasser 60° necter temporairement le câblage en s’assurant que par rapport à...

Table des Matières