Mitsubishi Electric Mr.SLIM PKA-M KA Série Manuel D'utilisation page 8

3. Operation
<Display of unsupported functions>
Title
Not available
Unsupported function
Return:
F1 F2 F3 F4
3.5.2 Vane·Vent. (Lossnay)
<Accessing the menu>
Main Main menu
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Main display:
Cursor Page
F1 F2 F3 F4
<Vane setting>
Fri
Swing Off Off
Vane Vent. Louver
F1 F2 F3 F4
Fri
Room
Cool Set temp. Auto
Mode Temp. Fan
<Vent. setting>
Fri
Low
Vent.
F1 F2 F3 F4
8
The message at left will appear if
the user selects a function not sup-
ported by the corresponding indoor
unit model.
Select "Vane·Louver·Vent. (Loss-
nay)" from the Main menu (refer to
page 7), and press the [SELECT]
button.
Press the [F1] or [F2] button to go
through the vane setting options:
"Auto", "Step 1", "Step 2", "Step 3",
"Step 4", "Step 5" and "Swing".
Select the desired setting.
Auto
Auto Step 1 Step 2
Step 3 Step 4 Step 5
Swing
Swing
Select "Swing" to move the vanes
up and down automatically.
When set to "Step 1" through "Step
5", the vane will be fixed at the se-
lected angle.
• under the vane setting icon
This icon will appear when the
vane is set to "Step 2" to "Step 5"
and the fan operates at "Mid 1" to
"Low" speed during cooling or dry
operation (depends on the mod-
el).
The icon will go off in an hour, and
the vane setting will automatically
change.
Press the [F3] button to go through
the ventilation setting options in the
order of "Off", "Low", and "High".
* Settable only when LOSSNAY unit
is connected.
Off Low High
Off Low
• The fan on some models of indoor
units may be interlocked with cer-
tain models of ventilation units.
<Returning to the Main menu>
Main Main menu
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Main display:
Cursor Page
F1 F2 F3
Note:
During swing operation, the directional indication on the screen
●
does not change in sync with the directional vanes on the unit.
Available directions depend on the type of unit connected.
●
In the following cases, the actual air direction will differ from the
●
direction indicated on the remote controller display.
1. While the display is in "STAND BY" or "DEFROST" states.
2. I mmediately after starting heat mode (while the system is wait-
ing for the mode change to take effect).
3. I n heat mode, when room temperature is higher than the tem-
perature setting.
<[Manual] To Change the Airflow's Left/Right Direction>
* The louver button cannot be used.
■
Model PKA-M·KA(L)
• Stop the unit operation, hold the lever of the louver,
and adjust to the desired direction.
* Do not set to the inside direction when the unit is in
the cooling or drying mode because there is a risk
of condensation and water dripping.
Caution:
To prevent falls, maintain a stable footing when operating the unit.
3.6. Ventilation
For LOSSNAY combination
■
The following 2 patterns of operation is available.
• Run the ventilator together with indoor unit.
• Run the ventilator independently.
Note: (for wireless remote controller)
R unning the ventilator independently is not available.
●
N o indication on the remote controller.
●
High
Press the [RETURN] button to go
back to the Main menu.
F4