Frequently Asked Questions - Philips LivingColors smartlink 69171 Mode D'emploi

To add a Philips LivingColors lamp to the remote
control, bring the remote close to the lamp,
then press and hold the "I" button. The lamp will
lash 3 times. Hold the "I" button until you hear
a beep from the remote; the lamp will shortly
lash in green. It is now connected to the remote
control and will turn to its last "on" setting.
For a LivingColors coloured and white light
lamp, please make sure that you also connect the
white light. You can do this in the same way as
LivingWhites products described in point 2.
If you would like to disconnect a LivingColors
lamp from the remote, bring the remote close to
the lamp, then press and hold the "0" button. The
lamp will lash 3 times. Hold the "0" button until
you hear a beep from the remote. The lamp will
now slowly fade to off.
2. You can also connect Philips LivingWhites
products (plugs, energy savers and luminaires)
to your remote control. To add a Philips
LivingWhites product, bring the remote close
to it, then press and hold the "I" button. The
lamp will lash 3 times. Hold the "I" button until
you hear a beep from the remote; the lamp will
rapidly lash twice. It is now connected to the
remote control and will turn to its last "on"
setting.
If you would like to disconnect a LivingWhites
product from the remote, bring the remote
close to the product, then press and hold the "0"
button. The lamp will lash 3 times. Hold the "0"
button until you hear a beep from the remote.
The lamp will now slowly fade to off.
3. You can also connect your remote control
to another remote control from the Philips
LivingAmbiance range. Any LivingColors or
LivingWhites remote with a SmartLink logo on
it can be connected to your remote control.
Connecting another remote control will allow
you to control the same lamps with two
different remotes. You could, for example, create
6 different lighting scenes—3 on one remote
and 3 on the other—with the same lamps.
To add an extra LivingColors or LivingWhites
remote control, do the following:
a. Reset the remote control you would like to
add: open its battery compartment and press
the RESET button for a few seconds (e.g. with
a paper clip). Make sure that the batteries are
in. The remote will play a sound to show it has
been reset.
b. Hold the remote you have reset close to your
current remote. Press the "I" button on both
remotes until the remotes play a sound. The
remotes are now connected – this means that
you can now connect the same lamps to the new
remote control and control all lamps with either
of the remotes.
c. If the remote you are adding is round, you can
now also copy it: you can immediately have
it connected to the same lamps your original
remote is connected to. In order to copy the
remote, repeat the procedure described in point
b.
Once you have connected one or more lamps
to your Philips LivingColors remote control, you
can control all of these lamps together or each
one individually.
To control a single lamp, you need to select it
(please note that for LivingColors coloured and
white light, coloured and white light need to be
selected separately). You can do this using one
of the light selection buttons. When you press
and hold one of the light selection buttons, the
selected lamp will start blinking. If this is not
the lamp you would like to adjust, release the
button and press it again; another lamp will
start blinking. When a lamp is selected, the light
selection indicator on the remote control (light
bulb) will light up. This means you can now adjust
the selected lamp only.
When no light is selected (light selection
indicator is off), all your adjustments will apply to
all lights connected to the remote control (for
example, you can dim all lights in the room).
If you like a particular combination of light
settings of different luminaires, you can also
store it as a scene in the same way as described
in section 2 of this manual.
4.

Frequently asked questions

What to do if...
• The LivingColors is not providing light
o Check the connections of the cord to the lamp.
Check that the plug is correctly placed in the
wall socket.
o Remove the power cord and put it back. If the
LivingColors changes several colours and then
goes off, use the remote control to switch it
back on.
• The LivingColors is not responding to the
remote control
o Check the batteries in the remote control. The
batteries should be correctly inserted (+ and -)
and should be charged. If the remote control is
18