Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
OPERATION
Note! Since the appliance and its heating elements are slightly greased when delivered,
there might be a slight development of smoke and odour the first time it is used. This is
harmless and stops after a short a while. Be sure to provide for sufficient ventilation
during such time.
Warning! Ensure that there is sufficient distance from the wall, fixtures or other appli-
ances. The distance must be at least 1 m to exclude the risk of fire.
INSTALLATION METHOD
1. Take the appliance out of the package.
2. There are 1 pc master device and 1 pc remote control in the package. (the base of the
device was non-detachable)
3. Check that the appliance shows no signs of damage before using.
CONTROL PANEL
CONTROL PANEL BUTTONS INTRODUCTION
Please be sure the main power switch is on "OFF" position.
●
Insert the plug into a suitable wall socket.
●
Turn the main power switch to "ON" position.
●
After switching on the power, you will hear a "BiBi" sound, the machine enters to Standby
●
Mode. (the power indicator lamp
Under standby model, press
key to turn on/off the appliance.
●
When switching it on the appliance works at the following default setting: Temperature
setting is automatically at 25°C, working at low heating power, LED displays room
temperature, swing off, timer off, fan working (no indicator light)
DISPLAY PANEL
light up)
In working condition, press
key to shift heating power between low and high,
●
light on for low heating power,
light on for high heating power.
In working condition, press
key to shift cooling fan between low and high power.
●
Indicator
light on for low fan power and indicator
Remark: The fan switch is only for cooling mode. The fan indicator will not light during
the heating mode.
Press
for heating mode and the cooling wind indicator
mode and the heating indicator
In working condition, press
key to make the device swing or not and the indicator
●
will be on / off accordingly.
Remark: In heating mode, when the room temperature is over the setting tempera-
ture, the heating element will stop working. Then fan will stop working after 10
seconds. At this time the swing function is not available.
In working condition, press key
●
a) Press
key, LED time indicator
timer (from 0 to12 hours), the timer will increase or decrease 1h by each pressing.
When pressing
or
for more than 2 seconds, the display will rapidly change and
you can quickly set the time.
b) Enter into the timer setting mode or the time-reset-mode can only be reached by
pressing
or
key.
c) If there is no operation to the keys after 5 seconds, then the LED indicator will show
the room temperature.
d) If the timer shows a different number than "0", the timer starts to run (without
display). If the timer reaches "0" the appliances turns off immediately and changes
into standby mode.
e) If the timer setting shows the value "0", then no timer has been set. The timer
indicator will be off and the LED display will show the current room temperature.
f)Press
key again, the timer setting is finished.
Press
key enter into temperature setting.
●
a)Press
key, changing the temperature by pressing
temperature will increase or decrease 1°Cby each pressing
b) If no operation to the keys after 5 seconds, then the LED indicator will show the
room temperature. When the temperature ≤-10°C,LED display"LO"; When the
temperature ＞ 40°C, LED display"HI".
c) If the device has been working for 10 seconds and the ambient temperature is above
the set temperature the heating function will be turned off automatically; after
another 10 seconds the fan will be turned off. If the ambient temperature is 1°C below
of the set temperature the heating function will restart and the indicator light turns on.
d) When setting the time and temperature at the same time, timing and the room
temperature will display interactively, interval is 30 seconds. When the timing is not
set, it only displays setting temperature.
light on for high fan power.
off; Press
off.
to the timer setting mode
will be on flicker . Then press
or
h
or
key from 15°C~ 35°C,the
54 | 55
GB
will
for cooling
to set the
Publicité
Table des Matières
