Table des Matières
Publicité
EN
IMPORTANT
Please read these instructions carefully before you start to assemble this greenhouse.
Keep these instructions in a safe place for future reference.
a Customer Service
For assistance with assembly or for replacement parts – please log onto our website or call
our service line (number is on the title page).
www.palramapplications.com
Additional information can be found at our website: www.palramapplications.com
a Safety Advice
It is of utmost importance to assemble all of the parts according to the directions. Do not
l
skip any step.
We strongly recommend using work gloves during assembly.
l
Always wear shoes and safety goggles when working with extruded aluminium.
l
If using a step ladder or power tools ensure that you follow the manufacturer's safety
l
advice.
Do not touch overhead power cables with the aluminium profiles.
l
Do not attempt to assemble the greenhouse in windy or wet conditions.
l
Dispose of all plastic bags safely keep them out of reach of small children.
l
Keep children away from the assembly area.
l
Do not lean against or push the greenhouse during construction.
l
Do not position your greenhouse in an area exposed to excessive wind.
l
Do not attempt to assemble this greenhouse if you are tired, have taken drugs or
l
alcohol or if you are prone to dizzy spell.
Hot items such as recently used grills, blowtorches etc. must not be stored in the
l
greenhouse. Ensure there are no hidden pipes or cables in the ground before
inserting the pegs.
This product is designed to use as greenhouse only.
l
a Care & Maintenance
When your greenhouse needs to be cleaned, use a mild detergent solution and rinse
with cold clean water. DO NOT use acetone, abrasive cleaners or other special detergents
to clean the clear panels.
a Tools & Equipment
Tape measure
l
Work gloves
l
Plastic or rubber mallet
l
Lubricant
l
Phillips head screwdriver
l
Step ladder
l
Drill bit
l
Large hammer
l
Scissors
l
Spanner
l
T001
l
a Before Assembly
This is a multi-part assembly best achieved
by two people. Allow at least half a day for
assembly process.
Selecting a site - the greenhouse must be
assembeld, positioned and fixed on a flat
level surface.
Choose a sunny position away from
overhanging trees.
We are strongly recomend to fix your
greenhouse directly to a solid concrete
foundation. When doing that use the pre
drilled holes in the metal base supplied.
Take out all components parts of the
packages. Sort the parts and check against
the contents parts list.
During assembly parts should be laid out
close at hand. Keep all small parts (screws
etc.) in a bowl so they do not get lost.
4 Prefix of the parts reference in the
assembly instructions:
A- Aluminum profiles and parts
P5XX– Polycarbonate panels
P3XX– Plastic parts
M– Metal parts
4XX– Screws, nuts, disks, etc.
TXX - Tools
Screws 411 and nuts 412 are used thruoghout the assembly process.
Screws 411 are to be assembled from the outside and nuts 412 from the
l
inside of the greenhouse.
Do not fasten screws and nuts (411 & 412) more than 2-3 turns only.
l
Do not tighten them until completion of the panels' assembly, if not specified otherwise.
a During Assembly
Carry out the assembly steps in the order set
out in the instructions.
Step 1: Make sure the base is square by
measuring the diagonals and level by using
a spirit level.
Step 2: Part A162 is the front door threshold.
Fixing it determines the front side of the
greenhouse.
Step 3: The end of all profiles, indicated by
an arrow, is always upward.
Step 5,6,7,12,15: The oval hole in the
crossbars A256 should always be assembled
to the base of the greenhouse.
Step 19,20: Decide on the window's
location before assembly. Window can be
installed in one of the indicated options.
Step 25: Panel glazing and sealing:
Do not assemble the next panel before the
previous one is fixed with its sealing strip.
Step 30: You may use Silicon
lubricant spray in order to help
you slide R303 into profile A173.
Step 40: Firmly connect the greenhouse
to a level final position immediately after
completion of the assembly.
Publicité
Table des Matières
