Introduction - Dexter power MS 8 Traduction Des Instructions D'origine

Introduction

NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
WE RECOMMEND:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device.
The operating instructions are intended to help the user
to become familiar with the machine and take advantage
of its application possibilities in accordance with the
recommendations. The operating instructions contain
important information on how to operate the machine
safely, professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in your
country. Keep the operating instructions package with
the machine at all times and store it in a plastic cover
to protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only
be operated by persons who were instructed concern-
ing the operation of the machine and who are informed
about the associated dangers. The minimum age re-
quirement must be complied with.
In addition to the safety notes contained in the present
operating instructions and the special regulations of
your country, the generally recognized technical rules
for the operation of machines must be observed.
Scope of delivery
• Open the packaging and carefully remove the device.
• Remove the packaging material and transport safety
devices (if applicable).
• Make sure that the delivery is complete.
• Make sure that the device and the accessories were
not damaged during transport.
• If possible, keep the packaging until the end of the
warranty period.
Legend of Fig. 1
1 Start button
2 Handle
3 Locking lever
4 Motor
5 Saw blade
6 Moving saw blade guard
7 Base
8 Table insert
9 Rotary table
10 Workpiece clamp
11 Housing / base joint
12 Dust bag
13 Stationary saw blade guard
MS 8
Scope of delivery
Tool for changing the saw
Tool for stop rail – 3mm Allen
Technical Data
Dimensions L x W x
H mm
Rotary table ø mm
Table height mm
Saw blade Ø mm
Number of teeth
Speed rpm
Cutting speed m/s
Pivot range
Tilt angle
Double mitre
45° x 45°
Catch positions
Weight kg
Cross-cutting data
Max. cut depth
90°/45°
90°/90°
90°/45°
45°/90°
45°/45°
Drive
Motor V/Hz
Rated input W
Technical changes reserved!
*S6, continuous operation periodic duty.
Identical duty cycles with a period at load followed by
a period at no load. Running time 10 minutes; duty cy-
cle is 25% of the running time.
The work piece must have a minimum height of
3mm and a minimum width of 10 mm.
Make sure that the workpiece is always secured
with the clamping device.
Mitre saw
Dust bag
Workpiece clamp
blade – 6mm Allen key
key
2 work piece supports
Support stand
2 batteries (AAA)
2 carbon brushes
Operating instructions
690 x 550 x 440
385 x 150
55
210/30/2,6
48
5000
55
2 x 45°
45°
left
45°, 30°, 22,5°, 15°, 0°,
15°, 22,5°, 30°, 45°
7,7
60 / 35 mm
120 x 60 mm
80 x 60 mm
120 x 35 mm
80 x 35 mm
220-240~ / 50
S6 25% 1500W
GB 19