Whirlpool WDP370PAHB Instructions D'utilisation page 6

To add rinse aid, turn the dispenser
cap to "Open" and lift off. Pour rinse
aid into the opening until the
indicator level is at "Full." Replace
the dispenser cap and turn to
"Lock." Make sure cap is fully
locked.
NOTE: For most water conditions, the
factory setting will give good results. If
you have hard water or notice rings or
spots, try a higher setting. Turn the
arrow adjuster inside the dispenser by
either using your fingers or inserting a
flat-blade screwdriver into the center of
the arrow and turning.
Select a Cycle (cycles vary by model)
Press the Select Cycles button until the light below the desired
cycle is on.
NOTE: Heavier cycles and options affect cycle length. Some
cycles and options will take up to 3¹⁄₂ hours to complete.
Heavy
– Use for heavily
soiled, hard-to-clean
items.
Normal - This cycle with
only the Heated Dry
option selected, and
without other options
selected, is
recommended to
completely wash and dry a full load of normally soiled dishes. The
energy usage label is based on this cycle and option combination.
ECO
– Use for lightly soiled items. It saves energy.
1-HR Wash
– Use for lightly soiled items. For fast results, 1-Hr
Wash will clean the dishes using slightly more water and energy.
Overnight cycle
– Use for loads with heavy amounts of food soil.
It is a longer cycle and therefore is ideal to run overnight.
Rinse Only
– (no options apply to this cycle) Do not use detergent.
This is only a rinse that keeps food from drying on your dishes and
reduces odor buildup in your dishwasher until you are ready to
wash a full load.
6
Lock
Refill
¹⁄₄ turn to lock
STEP 3
Select Options (options vary by model)
You can customize your cycles by pressing the options desired.
Repeatedly press the button until
6
the desired combination of options
is selected.
High Temp
– (can be selected with
Heavy and Normal wash cycles)
heats the water during the wash
portions of the cycle.
Sani Rinse
– (can be selected with
Heavy and Normal wash cycles)
Select this option to raise the water
temperature in the final rinse to approximately 155°F (68°C). Sani
Rinse option adds heat and time to the cycle. This high
temperature rinse sanitizes your dishes and glassware in
accordance with NSF/ANSI Standard 184 for Residential
Dishwashers. Certified residential dishwashers are not intended for
licensed food establishments.
Heat Dry
– (can be selected with 1-HR Wash, Heavy and Normal
wash cycles) When selected with the 1-Hr Wash cycle, the time is
increased by approximately 30 minutes.
4-HR Delay
– (any cycle) offers the choice to start the dishwasher
automatically at a later time. Select a wash cycle and options.
Press 4-HR Delay. Press START/RESUME. Close the door firmly.
Lock
– (on 4-HR Delay button) use to avoid unintended use of your
dishwasher. When Control Lock is lit, all buttons are disabled. The
dishwasher door can be opened while the controls are locked.
To turn on Lock:
Press and hold 4-HR Delay for at least 3 seconds. The Locked light
glows. If you press any pad while your dishwasher is locked, the
light flashes 3 times.
To turn off Lock:
Press and hold 4-HR Delay for at least 3 seconds. The Control
Lock light turns off.
Start or Resume a Cycle
Run hot water at the sink nearest your dishwasher until the
water is hot. Turn off water.
Push door firmly closed. The door latches
automatically. Select the wash cycle and options
desired OR press START/RESUME to repeat the
same cycle and options as in the previous wash
cycle. For top controls, select cycle and options
first, and then close the door.
You can add an item anytime before the main
wash starts. Open the door slowly and add the
item. Close the door firmly. Press START/
RESUME.
The Clean indicator glows when the cycle is
finished. Sanitized glows when Sani Rinse
option is selected and sanitization levels
occur.
STEP 4