Protocoles De Supervision; Catalogue Des Messages Syslog - Gorgy Timing LEDI NETWORK TDS V1 Mode D'emploi

8.5. PROTOCOLES DE SUPERVISION

8.5.1. Catalogue des messages Syslog

Le tableau ci-dessous décrit les messages Syslog envoyés par l'appareil.
Catégorie Gravité
user (1) Informational (6)
user (1) Informational (6)
user (1) Informational (6)
user (1) Informational (6)
user (1) Informational (6)
user (1) Informational (6)
user (1) Informational (6)
user (1) Informational (6)
user (1) Informational (6)
user (1) Informational (6)
user (1) Informational (6)
kern (0) Informational (6)
kern (0) Informational (6)
kern (0) Informational (6)
kern (0) Informational (6)
kern (0) Informational (6)
auth (4) Informational (6)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Notice (5)
daemon (3) Error (3)
daemon (3) Error (3)
daemon (3) Error (3)
ntp (12) Error (3)
98
- A new configuration has been defined.
- A new configuration has been defined through the front panel.
- A new configuration has been defined through the Telnet interface.
- A new configuration has been defined in the \"Alarms\" Webpage.
- A new configuration has been defined in the \"Inputs\" Webpage.
- A new configuration has been defined in the \"Interface\" Webpage.
- A new configuration has been defined in the \"Network\" Webpage.
- A new configuration has been defined in the \"NTP\" Webpage
- A new configuration has been defined in the \"PTP\" Webpage.
- A new configuration has been defined in the \"Output\" Webpage.
- A new configuration has been defined in the \"SNMP\" Webpage.
- System has restarted, reason : Reset / Power Failure.
- System has restarted, reason : User Request with Configuration Changes.
- System has restarted, reason : User Request without Configuration Changes.
- System has restarted, reason : Automatic for Configuration Changes.
- System has restarted, reason : Firmware Update.
- A Web interface has been accessed.
- A SNMP trap has been sent, with ID 4: NTP client software start learning environment&network
- A SNMP trap has been sent, with ID 5: NTP client software entering normal behavior
- A SNMP trap has been sent, with ID 6: Not enough replies of current synchronization server
- A SNMP trap has been sent, with ID 7: New server elected for synchronization
- A SNMP trap has been sent, with ID 8: NTP server software is starting
- A SNMP trap has been sent, with ID 9: The hardware is synchronized on its time reference
- A SNMP trap has been sent, with ID 10: The hardware is not synchronized on its time reference
- A SNMP trap has been sent, with ID 11: NTP server locked by the user
- A SNMP trap has been sent, with ID 13: NTP server software is rescaling on its PPS source
- A SNMP trap has been sent, with ID 14: NTP server software is rescaled on its PPS source
- A SNMP trap has been sent, with ID 15: Failure: no more time code and the time base has no more autonomy
- A SNMP trap has been sent, with ID 16: Warning: no time code. The time base has less than 3 minutes of
autonomy
- A SNMP trap has been sent, with ID 17: The hardware has never been externally synchronized
- A SNMP trap has been sent, with ID 19: Power supply is running again
- A SNMP trap has been sent, with ID 20: Input 1 is no more selectable
- A SNMP trap has been sent, with ID 21: Input 2 is no more selectable
- A SNMP trap has been sent, with ID 22: Input 1 is selectable
- A SNMP trap has been sent, with ID 23: Input 2 is selectable
- An error occurred with the SD-Card.
- Ethernet link connection.
- Ethernet link error. Check the cable.
- NTP Client with MAC address <MAC> from IPvX address <IP> has not requested any synchronization for
<duration> hour(s).
Corps
MDE-LEDI-NETWORK-TDS-4099V3.0