Inserting/Changing The Batteries - Bosch D-tect 150 SV Professional Notice Originale

16 | English
Universal detector
Max. altitude
Max. relative humidity
Pollution degree according
IEC 61010-1
Non-rechargeable batteries
Rechargeable batteries
Operating time, approx.
– Non-rechargeable batteries
(alkaline manganese)
– Rechargeable batteries
(2500 mAh)
Weight according to
EPTA-Procedure 01:2014
Dimensions (length × width ×
height)
Protection rating
A) See image
c
b
a
B) Depends on the size and type of the object, as well as the mater-
ial and state of the base material
C) Only non-conductive deposits occur, whereby occasional tem-
porary conductivity caused by condensation is expected.
The serial number (8) on the type plate is used to clearly identify your
measuring tool.
The accuracy and detection depth of the measuring
u
result may be negatively affected if the base material
is of poor quality.
For the signal test, which checks whether the measuring tool
is receiving a faulty signal, the conductivity criterion and
level are used that are defined in ETSI TS 103 361 (V1.1.1)
section 9.4.1 for an object depth of d=60 mm.
The following criterion for conductivity is used for the inter-
ference resistance test:
Under certain conditions (e.g. electrostatic discharge or ap-
plication of electromagnetic fields), the measuring results
may be lost and it may be necessary to reset the measuring
tool by removing and replacing the batteries.
Fitting

Inserting/changing the Batteries

It is recommended that you use alkaline manganese batter-
ies to operate the measuring tool.
Push the locking mechanism (5) in the direction of the arrow
to open the battery compartment cover (4) and remove the
battery compartment cover. Insert the batteries/re-
1 609 92A 4G1 | (28.08.2018)
chargeable batteries. When doing so, ensure that the polar-
D-tect 150 SV
ity is correct and corresponds to the diagram in the battery
2000 m
compartment.
90 %
The battery indicator (b) in the top status bar of the dis-
C)
2
play (16) indicates the state of charge of the batteries.
Note: Pay attention to the battery symbol as it changes to
4 × 1.5 V LR6 (AA) ensure that you replace the batteries in good time.
4 × 1.2 V HR6 (AA)
Please change batteries
5 h
7 h
measurements. Replace the batteries.
0.65 kg
To remove the battery/batteries, apply pressure to the rear
end of a battery as shown in the battery compartment cover
220 × 97 × 120 mm
diagram (1.). The front end of the battery is freed from the
battery compartment (2.), allowing the battery to be easily
IP 54 (dust and splash-
removed.
proof)
Always replace all the batteries at the same time. Only use
batteries from the same manufacturer and which have the
same capacity.
Take the batteries out of the measuring tool when you
u
are not using it for a prolonged period of time. The bat-
teries can corrode and self-discharge during prolonged
storage.
Operation
Protect the measuring tool from moisture and direct
u
sunlight.
Do not expose the measuring tool to any extreme tem-
u
peratures or variations in temperature. In case of
large variations in temperature, leave the measuring
tool to adjust to the ambient temperature before
switching it on. The accuracy of the measuring tool and
the functionality of the display may be compromised if ex-
posed to extreme temperatures or variations in temperat-
ure.
Do not attach any stickers or labels to the sensor
u
area (9) on the rear of the measuring tool. Metal labels
in particular will affect measuring results.
The use or operation of transmitters such as WLAN,
u
UMTS, radar, transmitter masts or microwaves in the
surrounding area may affect the measuring function.
Certain ambient conditions fundamentally impair the
u
measuring results. These include, e.g. the proximity of
devices that generate strong electric, magnetic or
electromagnetic fields, moisture, metal building ma-
terials, foil-laminated insulation materials or conduct-
ive wallpaper or tiles. Therefore, also refer to other in-
formation sources (e.g. construction plans) before
drilling, sawing or routing into walls, ceilings or floors.
If the warning message
<Please change batteries>
appears on the display (16),
the settings are saved and
the measuring tool switches
off automatically. It is no
longer possible to carry out
Bosch Power Tools