Comet KL 1300 Classic Notice Technique page 24

to be used.
• Do not use the high pressure cleaner if:
- the power supply cable or other important parts such as the high pressure pipe, the safety devices, the
cleaner gun and the lance are damaged;
- the high pressure cleaner has been tipped over or has been bumped;
- there are obvious leaks of water.
In these circumstances, the water cleaner should be tested by a Skilled Technician.
• It is especially important to pay great attention when the high pressure cleaner is used in areas where
there are moving vehicles as these can crush or damage the power supply cable, the high pressure pipe,
the cleaner gun etc.
• During operation, never leave the water cleaner unattended and make sure it is out of children's reach. Pay
particular attention when using it in kindergartens, nursing homes and old people's homes, as unsupervised
children, elderly people and disabled people may be present in such places.
• Before using the water cleaner, make sure it is in a dry place and that it is in a flat and stable position in
order to avoid accidents and prevent it from falling over.
• Before moving the water cleaner, follow the instructions in the "Switching off" section.
• Before starting the water cleaner, put on clothing which guarantees adequate protection against the
possibility of incorrect manoeuvres of the jet of pressurised water. Do not operate the water cleaner near
people unless they are also wearing protective clothing.
• High-pressure jets of water can be dangerous if they are not used properly. Do not point the jet in the
direction of people, animals, and energized electrical appliances or towards the water cleaner itself.
• Hold the cleaner gun firmly during use: when operating the lever (26), the operator is subjected to the
backlash of the high pressure. The power of this recoil is indicated in the table of technical specifications
(recoil is expressed in N, where 1 N = 0.1 kg).
• Do not point the jet towards oneself or other people in order to clean off clothing or footwear.
• To protect the environment, vehicle engines and machinery with oil-pressure circuits must only be cleaned
in areas with a suitable oil trap.
• Vehicle tyres must be cleaned at a distance of at least 50 cm/19 in to safeguard them from being damaged
by the high-pressure jet. The first evidence of damage to a tyre is a change in colour.
• Do not point the high-pressure jet towards materials, which contain asbestos or other harmful substances.
• Do not use the water cleaner in the rain.
• Pay particular attention to the instructions in the "Checks and connection to the mains electricity
supply" section.
• Pay particular attention to the instructions in the "Use with detergents" section.
• When the water cleaner is not in use, do not leave its plug in the power outlet and disconnect it before any
activity. More precisely, make sure that the mains switch (2) is in position "0", remove the plug from the
power outlet, press the lever (26) on the cleaner gun to eliminate any remaining pressure and bring the
safety catch in its locked position (25) (Fig. 4 - position S):
- before leaving the high power cleaner unattended, even for only a short time;
- after use; In addition, wait until the high pressure cleaner has completely cooled down before cleaning
or maintenance.
• During use, do not lock the lever (26) on the cleaner gun in the open position.
• Do not remove the plug from the power outlet by pulling on the power supply cable.
• Do not put any reducers or adaptors between the electric plug and the power outlet.
• Keep the power supply cable, any extension cords, the plugs and the outlets dry. Do not touch them with
wet hands.
• If the supply cord is damaged, it must be replaced by the Manufacturer or by a Skilled Technician, in order
to avoid a hazard.
• Do not cover the high pressure cleaner during operation and do not place it where there is inadequate
ventilation.
• When the high pressure cleaner is used in enclosed spaces, make sure that there is adequate ventilation.
5.1 Handling
• When handling the high-pressure cleaner, use the handling bar (3) as shown in Fig. 5 operation M.
• Use the lifting handle (10) for lifting Fig. 5 operation N.
24