Fender Super Champ X2 COMBO Mode D'emploi page 6

The Super Champ® X2 amplifier combines a real tube amp with modern
"extras" like versatile amp voicing and a wide palette of quality effects. It's
simple, toneful, and flexible. With computer hook-up, you can also custom-
tailor your amp's voicing and effects to your personal taste. There's no limit
to the number of tones that can be coaxed from this little firecracker, so your
practice and recording sessions will really come alive with the Fender® Super
Champ X2.
Features Include:
• 15 Watt tube power amp with two 6V6 tubes
• 12AX7 preamp tube
• 10 inch Fender Special Design speaker (combo amp)
• Voicing knob with 16 different amp types (Tweed, Blackface, British, Metal, etc.)
A. INPUT — Plug your guitar in here.
B. VOLUME 1 — Adjusts the loudness of Channel 1. This channel is voiced
for Fender Blackface™ clean tone.
C. CHANNEL SELECT — Press to switch channels.
Channel 1
D. GAIN — Controls preamp volume and the level of signal distortion for
Channel 2.
E. CHANNEL LED — Illuminates when Channel 2 is active.
Channel 1
F. VOLUME 2 — Use to set the overall loudness of Channel 2 after
adjusting GAIN {D}.
G. VOICE — Your Super Champ X2 comes equipped with 16 Channel 2
amplifier voicings, listed in the table below. You can customize this list
by using your computer and Fender® FUSE™ software available free of
charge at: fuse.fender.com.
1 Tweed Champ®
2 Tweed Deluxe™ clean
3 Tweed Deluxe™ dirty/compressed
4 Tweed Bassman®
5 65 Princeton® clean
6 65 Princeton® dirty/compressed
7 65 Deluxe™
8 65 Twin Amp™
9 60s British clean
10 60s British dirty/compressed
11 70s British
12 80s British
13 Super-Sonic™
14 90s Metal
15 2000 Metal
16 Jazzmaster™ (fl at, solid-state clean)
♫
Use the extreme flexibility of the VOICE knob wisely! Treble harshness or
boomy bass tones can be avoided by using the right guitar settings and
playing style for a particular amp voicing.
6 6
Super Champ® X2 Amplifier Super Champ® X2 Amplifier
Front Panel Front Panel
Channel 2
Channel 2
f e n d e r . c o m f e n d e r . c o m
• Two channels with channel-switching format (optional footswitch
available, P/N 0071359000)
• 15 effects with effects adjust control
• TAP tempo control for delay time/modulation rate adjustments
• External speaker capability
• ¼" Line output
• USB output for speaker-emulated digital recording
• software (free download) allows additional flexibility:
• • Change the amp's selection of amp voicing and effects defaults
• • Deep editing of effects parameters
• • Online access to free content from the Fender community
H. TREBLE/BASS — Adjusts the high- and low-frequency tone
characteristics of both channels.
I. F/X ADJUST — Adjusts the "main setting" of the active effect. For
most effects, this will be the effect level.
♫
You can observe and customize the F/X ADJUST knob functions,
and change the F/X SELECT effects list by using your computer and
Fender FUSE software.
J. F/X SELECT — Selects the active effect.
OFF 1 No Eff ect
VIBRATONE 1 Rotating Baffl e, Slow
2 Rotating Baffl e, Fast
DELAY 1 ~130ms (Slapback)
2 ~300ms
REVERB 1 Large Room
2 Concert Hall
3 Classic Fender® Spring Reverb
4 Reverb + Delay
CHORUS 1 Fast Sweep
2 Deep Sweep
3 Chorus + Delay
4 Chorus + Reverb
TREMOLO 1 Low Speed
2 Medium Speed
3 High Speed
K. TAP — Depending on the selected effect, the TAP button can be used to tap
in the delay time or modulation rate by pressing TAP rhythmically in sync
with the desired interval. The TAP LED blinks at the current delay/modulation
interval. Press the TAP button once to set the delay/modulation interval to its
maximum value.
FACTORY PRESET RESTORE — To restore all presets to their factory
!
settings: Press and hold the TAP button for 4 seconds until the TAP LED
lights up. Release the TAP button; the TAP LED will stay lit during the
restore process (about 5 seconds). When the TAP LED goes out, restore
is complete. You can backup valued presets before the restore function
is performed using Fender FUSE software.
L. POWER JEWEL — Illuminates when the unit is on.