Bosch AdvancedMulti 18 Notice Originale page 23

OBJ_BUCH-2966-001.book Page 23 Wednesday, March 8, 2017 9:58 AM
Removing (see figure B)
Open the AutoClic lever 1 all the way. The application tool/
accessory will be ejected.
Mounting and Adjusting the Depth Stop
The depth stop 15 can be used when working with segment
saw blades.
If required, remove an already mounted application tool/
accessory.
Slide the depth stop 15 over and beyond the tool holder 10 to
the stop onto the gear head of the power tool with the labelled
side facing upward.
The depth stop is intended for the following cutting depths:
– With segment saw blades ACZ 85 .. with a diameter of
85 mm: 8 mm, 10 mm, 12 mm and 14 mm cutting depths
(see indication on the depth stop in large font and not in
brackets).
– With segment saw blades ACZ 100 .. with a diameter of
100 mm: 14 mm, 16 mm, 18 mm and 20 mm cutting
depths (see indication on the depth stop in smaller font
and brackets).
Insert the appropriate segment saw blade for the desired cut-
ting depth. Slide the depth stop 15 from the tool holder 10 in
the direction of the application tool until you can rotate it free-
ly. Rotate the depth stop 15 so that the desired cutting depth
is above the section of the saw blade, which will be used to
saw. Slide the depth stop 15 once again to the stop onto the
gear head of the application tool.
For all other cutting depths and when working with other appli-
cation tools, remove the depth stop 15. For this, remove the
application tool and pull the depth stop from the gear head.
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:
Sanding disc Material
– All wooden materials
(e.g., hardwood, soft-
wood, chipboard, build-
ing board)
– Metal materials
Red quality
– Paint
– Varnish
– Filling compound
– Filler
White quality
Bosch Power Tools
Mounting the Auxiliary Handle (optional accessory)
The vibration-damped auxiliary handle enables the tool to be
used safely and more comfortably.
Screw the auxiliary handle 8 on the right or left of the machine
head depending on the working method.
 Do not continue to use the power tool when the auxilia-
ry handle is damaged. Do not make any changes or
modifications to the auxiliary handle.
Mounting/Replacing a Sanding Sheet on the
Sanding Plate
The sanding plate 13 is fitted with Velcro backing for quick
and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 14, free the Velcro back-
ing of the sanding plate 13 from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet 14 flush alongside one edge of the
sanding plate 13, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet 14, grasp it at one of the tips and
pull it off from the sanding plate 13.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
Application
For coarse-sanding, e.g. of rough, unplaned beams and
boards
For face sanding and planing small irregularities
For finish and fine sanding of wood
For sanding off paint
For sanding primer (e.g., for removing brush dashes,
drops of paint and paint run)
For final sanding of primers before coating
English | 23
Grain size
coarse 40
60
medium 80
100
120
fine 180
240
320
400
coarse 40
60
medium 80
100
120
fine 180
240
320
1 609 92A 3B0 | (8.3.17)