Stid ARCHITECT BLUE Notice D'installation page 3

ARCS Blue
Upgradable readers
Installation instructions
Read-only reader: automatic tamper management (except touch screen) or activated on the reading of a valid identifier
Touch screen read-only reader: if the bell is activated, contact J2 is used to connect the external ring (max. 200 mA at 28 Vdc).
Read/Write & OSDP readers: the relay is controlled by the SSCP
TM
Reader powered off. The defaults reader settings can be stored in internal memory accessible by UHF RFID technology. They will be taken into account when the
reader is powered on.
R and S readers are configurable with SCB RFID / virtual configuration card.
OSDP readers are configurable with OCB RFID / virtual configuration card or with FileTransfer command.
TM
If the SCB/OCB is compatible with the reader's firmware, the LED lights green and the buzzer beeps five times.
▪
If the SCB/OCB is not compatible with the reader's firmware, the LED lights red and the buzzer is activated for 1 s.
▪
If the SCB/OCB key is different from the reader's key: no reaction.
▪
Caution: set your reader with your own company key.
On power-up, the reader enters an initialization phase:
1. Activation of the white LED and buzzer for 100 ms.
For read-only & OSDP readers:
TM
2. Activation of the LED, according to the color code: Red = +10, Orange = +5, Green = +1, indicating the firmware version.
3. For serial R/S reader only: the orange LED flashes 20 times: waiting for an update.
4. For Bluetooth reader only: Activation of white fixed LED during Bluetooth® initialization.
®
5. Activation of the default LED (read-only: flashes blue, OSDP
6. For the ARC screen with an activated keypad, the default mode is: display the picture on standby and activate the keyboard by pressing the screen.
▪ For optimal operation, the biometric sensor must be free of all traces of water. Outdoors it is recommended to install the reader under cover.
▪ The keypad is sensitive. Take off your gloves to enter your code.
Caution: at the reader Bluetooth® (BT1/BT2) powering, make sure that nothing is in an area of at least 10 cm / 3.94 in. around the reader (ex. No hand in
front of the reader...).
▪ The supply voltage at the reader's connector should be between +7 Vdc and +28 Vdc.
▪ As far as possible, keep the reader away from computer or power source cables. They can generate electrical interference, depending on their radiation level and
the proximity of the reader.
▪ Recommended distance between two readers: parallel plane: 15.8 in – same plane: 15.8 in – perpendicular plane: 11.8 in.
▪ Recommended distance between two Bluetooth
▪ Place the reader at a height of less than 2 meters / 78.74 inch (standard UL/IEC 62368).
▪ If the reader is fixed on a metal surface, it is possible to have a reduction in the reading distance.
▪ Use a ferrite (two-way) for the cable (power supply and data). Example: reference 74271222 WURTH ELEKTRONIK.
▪ For ARCS screw terminal output reader, connect the 2.2 µF capa (provided) between +12V and GND directly to the output of the connector (no polarization).
▪ By design, the reader can be installed indoors and outdoors.
▪ BEFORE powering on, connect the wires or the connector of the reader. Before disconnecting the wires or the connector of the reader, power off.
▪ Operating temperature:
Temperature
Readers
For data signals, 10k pull-up resistors are connected internally to V
Available Baud rate
Factory Baud rate
Mode
Number of bits
Transfer mode
Stop bit
RS485
Wiring resistors R1 and R2 use extended features
of the RS485 bus: FAIL-SAFE (see RS485-AN-960).
R1 & R2: 1.5 kΩ resistor supplied.
R : 120 Ω end-of-line resistor supplied.
T
STid reserves the right to make change without notice, for the purpose of product improvement.
ARCS Blue
Lecteurs évolutifs
Notice d'installation
/OSDP
®
UHF default configuration settings
Read-only reader configuration
TM : off; if no customer specific configuration).
Precautions for the biometric sensor and keypad
Caution for Bluetooth® reader
® readers: 2 meters / 78.74 inch either plan.
-22 °F to 158 °F -22 °F to 140 °F
-30°C to +70°C -30°C to +60°C
A, B, IM, JM AQ, BQ
in
9600, 19200, 38400, 57600, 115200 bauds
ARC R & S: 9600; ARC W: 38400 (SSCP
© STid - 20 PA des Pradeaux FR13850 Gréasque - NI1114C09- Page 2 sur 18 - Ed. 02/07/2021
Relay
protocol commands.
TM
Powering-up the readers
Precautions for installation
-4 °F to 158 °F
-20°C to +70°C
C, I, J, K, KM
TTL pull-ups
(power supply voltage) for optimal wiring distances.
RS485 communication
), 9600 (OSDP
®
Asynchronous
8
LSB first
1
Default broadcast address 00h
Bus architecture (RS485)
ARCS Blue
Lectores escalables
Procedimiento de instalación
conforme con NOM-024 -SCFI-2013
-4 °F to 140 °F 14 °F to 122 °F
-10°C to +50°C
-20°C to +60°C
CQ D, E, F
)
TM
More
reader
are available
protocol specification
US
FR
ES
details about
communication
in the