General Information - Novy 800.995 Instructions D'installation

GENERAL INFORMATION

General
This is the instruction for the installation kit for remote installation of the motor. Carefully read these instructions before
installing and commissioning the build-in unit. It is recommended to have one or more qualified persons carry out the
installation only.
Important before installation
Page 2 of these installation instructions show the installation drawings. Observe the following installation tips before
starting the installation activities:
• For easier installation of the wall-mounted chimney hood, it is recommended to do this with at least 2 persons.
• Check if all installation materials have been supplied using the drawing on page 2.
• Make sure that the wall against which the motor unit is installed has sufficient load bearing capacity.
• The motor unit must be installed in-house.
• ATTENTION! Keep the motor shaft horizontal.
INSTALLATION
Proceed following the installation drawings on page 2.
Uninstall the motor unit of the build-in unit. Look at the type number of the hood.
1
For types 894 / 895 / 896/ 897/ 898/ 899:
Open the bottom plate by pulling it open on the front side with a downward movement. Then remove the bottom
plate by loosening the clamping plates at the hinges and slide them. Do not fully unscrew the screws of the clamping
plates. Then snap out the bottom plate from the pins.
Now take the aluminium fat filter from the hood. You see 6 screws on the inside of the hood with which the motor
unit has been installed onto the build-in unit. Unscrew these 6 screws. Now the motor unit is released from the hood.
Attention! When putting back the bottom plate do not forget to slide back the clamping plates over the pins and to
tighten them with screws.
Open the bottom plate by gently pulling it open. Now take the aluminium fat filter from the hood. You see 6 screws
on the inside of the hood beside the guard grid with which the motor unit has been mounted onto the build-in unit.
Unscrew these 6 screws. Now the motor unit is released from the hood.
Screw the flange plate 832018 onto the motor unit with 8 of the supplied screws (906151).
2
Screw the other flange plate onto the build-in unit (flange plate 812018 for types 894, 895, 896, 897, 898, 899, 810
3
and 811 and flange plate 832018 for types 820, 821, 822 and 823). Use the insulation strip 801006 by sticking it onto
the bottom side of the flange plate. Use the screws 906151 to install the flange plate onto the build-in unit.
Determine the place where you want to place/hang the motor unit. If necessary, the exhaust direction of the motor
4
unit can be changed by removing 8 screws from the motor cover and turning the motor cover a quarter turn. Before
fastening the 2 brackets 832022, remove the screws of the motor cover on the side on which you want the suspension
brackets to be placed. Attach the suspensions brackets onto the motor unit using the original screws.
Install the motor unit onto the wall. Attention! Do not attach the motor to the ceiling. For this use the supplied screws
5
and any plugs, if necessary. The supply and exhaust pipes can be made in a 90° angle or in a straight line.
Use for all hood models a duct of Ø150 mm between the build-in unit and the motor unit. For the 810, 811, 822, 823,
6
894, 895, 896 en 897 the exhaust duct of the motor unit to the outside has a 125 mm diameter. For the 820, 821, 898
and 899 the exhaust duct to the outside has a 150 mm diameter.
Attach the exhaust duct to the flange plate on the build-in unit and on the motor unit using a hose clamp or aluminium
tape.
Connect the supplied cable (8999002) between the build-in unit and the motor unit using the connectors. The length
7
of this cable is 5 m. Optional, you can order an extra extension cable (7000.092), resulting in a total cable length of
10 m.
Install the build-in unit into the recess as described in the installation instruction of the build-in unit concerned.
EN 7