Beamz MHL810 Manuel D'instructions page 5

SLND - This will let you set unit as a master or slave in a
master/slave configuration.
1. Press the MENU button until "SLND" is displayed, press ENTER. Either
"MAST", "SL 1", or "SL 2" will be displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, press
ENTER to confirm.
NOTE: In a Master/Slave configuration you can set one fixture to Master and
then set the next fixture to "SL 2", the fixtures will now have contrast movement
to each other.
SHND - Show modes 0-12 (Factory programs). Show mode can run
with or without sound active mode active.
1. Press the MENU button until "SHND" is displayed, press ENTER.
2. "Sh X" will now be displayed, "X" representing a number between 0-12. Use the UP or
DOWN buttons to find your desired show.
3. When you have found your desired show press ENTER, then press and hold the
MENU button for at least 3 seconds to activate. After you have set your desired show, it
can be changed at any time using the UP or DOWN buttons.
NOTE: Blackout function ashould be off (BLND = NO), otherwise the show will not work.
SOUN - Sound Active mode.
1. Press the MENU button until "SOUN" is displayed, press ENTER.
2. The display will show either "ON" or "OFF". Press the UP or DOWN buttons to select
"ON" to activate sound active mode, or "OFF" to deactivate sound active mode.
3. Press ENTER to confirm.
SENS - In this mode you can adjust the sound sensitivity.
1. Press the MENU button until "SENS" is displayed, press ENTER.
2. A number between 0-100 will be displayed. Press the UP or DOWN buttons to adjust
the sound sensitivity. 0 being the least sensitive, and 100 being the most sensitive.
3. When you have found your desired setting press ENTER to confirm.
BLND – Blackout mode.
1. Press the MENU button until "BLND" is displayed, press ENTER.
2. The display will show either "YES" or "NO". Press the UP or Down buttons to select
"YES" to activate the blackout mode, or "NO" to activate the normal mode.
3. Press ENTER to confirm.
LED - With this function you can have the LED display turn off after 10
seconds.
1. Press the MENU button until "LED" is displayed, press ENTER.
2. The display will show either "ON" or "OFF". Press the UP or DOWN buttons to select
"ON" to keep the LED display on at all times, or "OFF" to switch to have the LED display
switch off after 10 seconds.
DISP - This function will reverse the display 180º.
1. Press the MENU button until "DISP" is displayed, press ENTER.
2. Press ENTER to "flip" the display. Press ENTER to "flip" it again. Press ENTER when
you have made your desired setup.
3. Press ENTER to confirm. To make you LED display reappear again press any button
1TIL – Tilt 1 inverse
1. Press the MENU button until "1TILT" is displayed, press ENTER.
2. The display will show either "YES" or "NO". Press the UP or Down buttons to
select "YES" to activate the tilt inversion mode, or "NO" to activate the normal
mode.
3. Press ENTER to confirm.
2TIL – Tilt 2 inverse
1. Press the MENU button until "2TILT" is displayed, press ENTER.
2. The display will show either "YES" or "NO". Press the UP or Down buttons to
select "YES" to activate the tilt inversion mode, or "NO" to activate the normal
mode.
3. Press ENTER to confirm.
REV –
1. Press the MENU button until "REV" is displayed, press ENTER.
2. The display will show either "YES" or "NO". Press the UP or Down buttons to
ENTER
MODE
UP
DOWN
UP
DOWN
ENTER
MODE
UP
DOWN
ENTER
MODE
UP
DOWN
ENTER
MODE
UP
DOWN
ENTER
MODE
UP
DOWN
ENTER
MODE
UP
DOWN
ENTER
MODE
UP
DOWN
ENTER
MODE
UP
DOWN
ENTER
MODE
UP
DOWN
ENTER
MODE
UP
DOWN
5