Clatronic HMS 2739 Mode D'emploi & Garantie page 27

Masquer les pouces Voir aussi pour HMS 2739:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
Instructions for Use
Always choose a utensil and a speed according to the following
table:
Product/Type of
Max.
Preparation
Quantity
Heavy dough (e.g.
500 g
yeast dough)
Cake mixture, Dres-
750 g
sings, Desserts
Sponge mixture, wafer
750 g
mixture, Cream
Liquids, shakes
up to 1 l blender 5 or turbo 1 min.
With heavy mixtures, do not operate the machine for more
than 3 minutes, and then allow it to cool down for a further
10 minutes.
Depending on the consistency of the mixture it is necessary
to remove the mixture from the edge of the mixing bowl and
place it back on the kneading attachments. The device must
be turned off.
Releasing the kneading hook / beater
1. In order to release the kneading hook/whisk (10) turn the
power level selector switch to „0" and ensure that the mixer
has been disconnected from the mains.
2. Press the button (2) to release the kneading hook/whisk.
Remove the device by turning it slightly.
NOTE:
The hooks can only be removed if the speed switch (3) is in
the „0" position.
Turbo operation
This is for switching to maximum speed for a short time. Press
at short intervals for pulsed mode operation.
CAUTION:
Do not use this function for more than one minute!
How to use the Blender
1. Turn the power level selector switch (3) to „0" and ensure
that the mixer (1) has been disconnected from the mains.
2. On the back of the mixer push the cover of the installation
aperture upwards.
3. Place the fast mixing rod on the installation aperture in such
a way that the two arrows are pointing one above the other.
To lock the rod in place, turn it through approximately 90° in
a clockwise direction.
4. Insert the mains plug into a properly installed 230 V/50 Hz
safety power socket.
5. Place the fast mixing rod into a high-walled, partly-fi lled
vessel.
CAUTION:
Do not operate the fast mixing rod when the vessel is
empty, i.e. when there is no food in the vessel to be mixed.
05-HMS 2739 New.indd 27
05-HMS 2739 New.indd 27
Max
Ope-
Utensil
Level
rating
Time
kneader
1 - 4
3 min.
hook
beater
2 - 5
5 min.
beater
2 – 5
5 min.
6. Select a speed using the power level selector switch (3).
Move the fast mixing rod slightly up and down.
7. When you would like to stop mixing, turn the power level
selector switch to „0" and unplug the device from the mains.
How to use the Kneader hooks/beater
1. Turn the power level selector switch (3) to „0" and ensure
that the mixer (1) has been disconnected from the mains.
2. Press the end of the kneader hooks/beater (10) into the cor-
responding mixer openings until the hooks click into place.
While pressing, turn slightly in order to facilitate the whole
operation.
NOTE:
Please note that the kneading hook with the curved was-
her on the shaft can only be inserted on the left-hand side
of the mixer when viewed from the bottom.
3. Insert the mains plug into a properly installed 230V/50 Hz
safety power socket.
4. The handmixer (1) can be used at various speeds set with
the speed regulator (3).
How to use the Mixer stand
Please select a fl at non-slip surface for the mixer stand.
1. Place the hand mixer (1) on the upper section (5) of the
mixer stand (11). Please check whether the clip (12) of the
upper section is locked in place on the back of the mixer.
2. Mount the hooks as described above in the section "How to
use the Kneader hooks/beater".
3. In order to place the mixing bowl (8) underneath, pull the clip
(6) to unlock the upper section of the mixer stand (5) and
fold the mixer upwards.
4. Place the mixer bowl fi lled with the desired ingredients onto
the revolving plate (7). Now fold the mixer down again.
5. Insert the mains plug into a properly installed 230V/50 Hz
safety power socket.
6. The handmixer (1) can be used at various speeds set with
the speed regulator (3).
7. The revolving plate turns automatically!
8. When you would like to stop mixing, turn the power level
selector switch to „0" and unplug the device from the mains.
9. When you have fi nished pull the clip (6) again to unlock
the upper section of the mixer stand (5) and fold the mixer
upwards.
10. Now the mixer bowl can be removed. Remove the hooks
as described above in the section "Releasing the kneading
hook / beater".
11. In order to separate the mixer from the upper section (5) of
the mixer stand, pull the mixer upwards.
Cleaning
Before cleaning the equipment, always remove the mains
plug from the socket.
Only a damp cloth should be used for cleaning the outside
of the machine.
Under no circumstances should the device be immersed in
water for cleaning.
27
04.06.2008 10:05:11 Uhr
04.06.2008 10:05:11 Uhr

Publicité

Table des Matières
loading

Table des Matières