Replacing Batteries - Warn 90288 Guide D'installation Et Operateur

STEP 5: MOUNT THE HOLSTER
WAR N I N G
For ATV use, the typical location for the holster is on the left
TO AVOID SERIOUS INJURY
handlebar.
OR DEATH:
•
• Always use caution when moving
•
or repositioning any vehicle controls
•
so as to not compromise the safe
operation of the winch or vehicle. Select
a mounting position that will provide
clearance for all vehicle controls.
• Never attempt to bypass receiver
•
by connecting switches directly to
contactor.
•
STEP 6: SYSTEM CHECK
1. Insure that wiring to all components is correct and all loose
2. Insure that there are no exposed terminals or wiring. Cover
3. Turn ATV ignition switch to the ON position.
4. Check winch for proper operation using the handlebar
5. Press and hold both buttons on the wireless handheld remote
CAUT I ON
6. By pressing the buttons on the remote, verify that the winch
ALWAYS KNOW YOUR WINCH:
Before doing a system check, take time

REPLACING BATTERIES

to fully understand your winch and the
winching operation by reviewing the Basic
If the indicator light on the handheld remote flashes RED during
Guide to Winching Techniques, included
winching, the batteries are low and should be replaced.
with your winch.
1. Remove the two screws from the handheld remote.
2. Separate the top and bottom sections of the remote using a
3. Remove the old batteries and dispose in accordance with local
4. Insert new alkaline batteries as shown with the positive
5. Join the top and bottom sections making sure that they snap
6. Secure with the two screws.
The holster clamp must be mounted before assembly
Do not tighten over any hoses, cables, or wiring.
For ATVs, it is recommended that the holster be clamped on
the left handlebar. The clamp is designed to prevent rotation.
If necessary, a piece of electrical tape around the handlebar
may be used to prevent slipping.
For UTVs, the holster may be mounted on the dash or other
convenient surface using two #10 or M5 machine screws and
locknuts.
Assemble the holster as shown. Holster may be oriented in
any one of eight positions.
wires are securely tie wrapped.
any bare terminal with terminal boots, heat shrink tubing or
electrical tape.
switch. The wire rope should spool in and out in the direction
indicated on the switch. If winch functions correctly, proceed
to the next step. Otherwise troubleshoot.
until the GREEN indicator light comes on. The wireless system
is now active and ready to use.
powers IN and powers OUT properly.
coin or screw driver.
environmental regulations.
terminals facing the switches. Do not mix old and new
batteries.
together and rubber seal remains intact.
8
OPERATION
This WARN Wireless Control System has
been designed
Turn on sequence:
to minimize interference
1. Activate the system by pressing both buttons on the wireless
from other sources of radio.
C AUTI ON
2. The winch system is now operational.
3. Press the power IN button or power OUT button as needed.
TO AVOID MINOR OR MODERATE INJURY:
Turn off sequence:
• Always be aware that obstacles and other
radio transmission sources may affect
1. Deactivate the system by pressing both buttons on the
performance.
• Always insure the matching WARN
transmitter is closer to its receiver
than other transmitters in use during
winching.
CAUT ION
TO AVOID MINOR OR MODERATE INJURY:
• Always use handlebar switch or
wired remote when intermittently
"jogging" winch.
IN
OUT
Press and hold both
buttons for 3 seconds to
deactivate the wireless
TROUBLESHOOTING
If the winch does not power in or out when remote buttons are pushed:
1. Check that the wireless system has been activated (GREEN LED on remote is ON).
2. Check all electrical connections. Verify that connections follow the wiring diagram and instructions.
3. Insure that 10 seconds have passed since the standard wired control system was last used.
transmitter simultaneously and holding for 3 seconds until
GREEN light illuminates.
wireless transmitter simultaneously and holding for 3 seconds
until GREEN light turns off.
LED Indicator Light
Steady GREEN - system active and ready to use
Steady RED - winch powering in or out
Flashing RED during winching - battery low
LED indicator light
Power IN
Power OUT
Press and hold
both buttons
for 3 seconds to
activate wireless
system.
9
system.