GBC Swingline CombBind C110E Manuel D'utilisation page 5

How to bind
Measure document using colour coded guide
1
(fig.1)
Select comb which fits your document (fig.2)
2
Use the table to choose a suitable comb size. Please
note that this guide is based on 20lbs/80gsm paper. The
sheet capacity of combs will vary depending on the type
and thickness of the cover sheets you have chosen. If in
doubt select the next comb up in capacity.
Load comb onto machine (fig.3)
3
Insert the binding comb next to the white positional
arrow on the machine, behind the metal comb support
fingers, with the open side of the comb pointing
upwards.
Note: If using Swingline
arrow on your comb should align to the white arrow on
the machine.
Open comb by turning lever towards you (fig.4)
4
The coloured arrows adjacent to the opening comb
act as a guide as to how far to open in order to allow
punched sheets to be easily inserted.
Note: If using Swingline
coloured line on your comb should align to the coloured
arrows on the machine for faster binding.
Select document size (fig.5)
5
Rotate the edge guide to the paper / cover size you
wish to bind; A4 (297mm x 210mm) or Letter (8 1/2"
x 11"). When using oversized covers, rotate the edge
guide to the oversize position, punch the covers for your
document and set aside. Then rotate the edge guide to
select either A4 or Letter and proceed.
Load pages into slot (fig.6)
6
You can punch 2 cover sheets (0.2mm) or up to 15
sheets of paper (20lbs/80gsm) at a time. Select the
quantity of sheets to punch and tap the edge of the
sheet stack against a flat surface to ensure that all
sheets are aligned. Push the side of the stack to be
punched into the punching slot as far as it will go, and
slide left to align with the edge guide. When properly
aligned, both of the two red flags visible on the top
cover of the binder will turn green.
Maintenance
Please ensure that the
clippings tray is emptied on a
regular basis. This will prevent
blockage and ensure that the
unit is always ready to punch.
The clippings tray can be
accessed from the back of the
machine.
In order to prevent overloading never try and punch more
than the maximum numbers of sheets recommended (15
sheets of 20lbs/80gsm). The unit is maintenance free if
handled correctly.
GBC ProCombs™ the white
™ ®
GBC ProCombs™ the
™ ®
Punch pages (fig.7)
7
Press the ON / OFF button
to indicate that the power is on. And the punch button
will light up in green.
To punch, press the illuminated green punch button
When finished punching turn the machine OFF by
pressing the ON / OFF
If the punch jams the red jam light
indicate that the machine has jammed. The machine
will automatically reverse the punches to clear the jam
and the red jam light will remain illuminated. Remove the
paper and push the punch button to re-set the machine.
The red jam light will turn off indicating that the machine
is ready to punch. Reduce some of the sheets and
repeat steps 2 to 4 to avoid jams on additional lifts.
Note: If the red light remains on, unplug the unit and
contact an authorised GBC service representative for
any required repairs.
When finished punching turn the machine OFF by
pressing the ON / OFF
Combine pages with comb (fig.8)
8
Remove the sheets from the punch slot and insert onto
the fingers of the binding comb.
Repeat process as required
9
Repeat stages 6-8 until your document is fully loaded
on the comb.
Close (fig.9)
J
Close comb and remove document.
Service
Contact an authorised Swingline
representative for any required repairs.
o
US
. A blue light will illuminate
button.
will illuminate to
button.
GBC service
™ ®
.
5