• spray gun;
• lance hose;
• professional fixed fan-shaped nozzle;
• water inlet quick-fit connection kit;
• external detergent suction hose kit;
• handle for transporting and manoeuvring (Classic model);
• handle fixing kit (Classic model);
• instruction manual - safety precautions;
• instruction manual - operation and maintenance;
• warranty certificate;
• after-sales centre booklet;
• EC declaration of conformity;
• nozzle cleaning pin.
In case of problems, contact your dealer or an authorised after-sales centre.
The standard fittings of the high-pressure cleaner can be integrated with the following range of
accessories:
•
type water mains disconnector: mandatory for connecting up to the drinking water mains.
BA
• sandblasting lance: designed to clean surfaces, eliminating rust, paint, scale, etc.;
• drain cleaning kit: designed to unblock pipes and ducts;
• rotating-nozzle lance: designed to remove resistant dirt;
• foam lance: designed for more effective detergent distribution;
• lances and nozzles of various types.
• Put the power cable support (10) on the sheet metal plate of the handle (8) and fix it with the self-
tapping screw (11).
opEration
• Insert the handle (8) in the steel pipes projecting from the machine and fix it using the kit supplied:
tighten the threaded handwheels (12) on the nuts retained by their housings on the handle.
. 2
.
of fig
• In the Classic model, connect quick-fit connection (22) of hose (20) to the water outlet connection.
g
. 5
.
opEration
of fig
• In the Classic model, screw up the connection (21) of the high-pressure hose to the thread (18) of the
spray gun (13) and tighten well using two 22 mm fixed wrenches (not supplied).
• In the Extra model, screw the high-pressure hose connection of the hose reel onto the coupling (19)
of the spray gun (13) and tighten well using two 22 mm fixed wrenches (not supplied).
. 6.
fig
• Fit the filter (30) in the water inlet connection (29). Fit the seal (31) in the water inlet quick-fit
connection (32) and screw up to the connection (29).
• Move the high-pressure cleaner to work position.
• This machine can be used indifferently vertically (
• In the Classic model, Completely unwind the high-pressure hose (20).
• If your machine has a hose reel (5) release it by turning knob (27) anticlockwise; unwind enough hose
by turning the reel clockwise with the crank (26); lock the device by turning the knob (27) clockwise.
• Fasten a supply hose with inner diameter 19 mm/0.75 inches to the water inlet quick-fit connection (32),
using an ordinary gardening quick-fit connection.
• Open the water supply tap and make sure this is not dripping;
- if the connection is made to the drinking water mains, a
be used, in conformity with EN 12729 standard, and available from your dealer (
to its use, refer to the relative instruction manual;
- in case of supply from a water tank, introduce the suction hose inside the tank and make sure the vertical
distance between the water level and the pump is no more than 1.5 m (4.9 ft).
OPTIONAL ACCESSORIES
INSTALLATION - FITTING ACCESSORIES
a
. 2
.
of fig
OPERATION - PRELIMINARY ACTIVITIES
d
. 4.
opEration
in fig
a ") or horizontally (
. 2,
"
fig
rEfErEncE
H
. 5.
opEration
in fig
type water mains disconnector (38) must
BA
B
opEration
f
. 5.
opEration
in fig
l
opEration
in
b ")
. 2,
"
fig
rEfErEncE
. 6).
With regard
fig
M
. 6.
opEration
in fig
EN
21