Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Time Difference Table
Delay
Distance
Distance
Number
(cm)
(inch)
0
0.0
0.0
1
3.4
1.3
2
6.8
2.7
3
10.2
4.0
4
13.6
5.4
5
17.0
6.7
6
20.4
8.0
7
23.8
9.4
8
27.2
10.7
9
30.6
12.1
10
34.0
13.4
11
37.4
14.7
12
40.8
16.1
13
44.2
17.4
14
47.6
18.8
15
51.0
20.1
16
54.4
21.4
17
57.8
22.8
18
61.2
24.1
19
64.6
25.5
20
68.0
26.8
21
71.4
28.1
22
74.8
29.5
23
78.2
30.8
24
81.6
32.2
25
85.0
33.5
26
88.4
34.8
27
91.8
36.2
28
95.2
37.5
29
98.6
38.9
30
102.0
40.2
31
105.4
41.5
32
108.8
42.9
33
112.2
44.2
34
115.6
45.6
35
119.0
46.9
36
122.4
48.2
37
125.8
49.6
38
129.2
50.9
39
132.6
52.3
40
136.0
53.6
41
139.4
54.9
42
142.8
56.3
43
146.2
57.6
44
149.6
59.0
45
153.0
60.3
46
156.4
61.6
47
159.8
63.0
48
163.2
64.3
49
166.6
65.7
50
170.0
67.0
18
-EN
Delay
Distance
Distance
Number
(cm)
(inch)
51
173.4
68.3
52
176.8
69.7
53
180.2
71.0
54
183.6
72.4
55
187.0
73.7
56
190.4
75.0
57
193.8
76.4
58
197.2
77.7
59
200.6
79.1
60
204.0
80.4
61
207.4
81.7
62
210.8
83.1
63
214.2
84.4
64
217.6
85.8
65
221.0
87.1
66
224.4
88.4
67
227.8
89.8
68
231.2
91.1
69
234.6
92.5
70
238.0
93.8
71
241.4
95.1
72
244.8
96.5
73
248.2
97.8
74
251.6
99.2
75
255.0
100.5
76
258.4
101.8
77
261.8
103.2
78
265.2
104.5
79
268.6
105.9
80
272.0
107.2
81
275.4
108.5
82
278.8
109.9
83
282.2
111.2
84
285.6
112.6
85
289.0
113.9
86
292.4
115.2
87
295.8
116.6
88
299.2
117.9
89
302.6
119.3
90
306.0
120.6
91
309.4
121.9
92
312.8
123.3
93
316.2
124.6
94
319.6
126.0
95
323.0
127.3
96
326.4
128.6
97
329.8
130.0
98
333.2
131.3
99
336.6
132.7
Setting the Time Correction Unit
You can change the unit, (cm or inch) of time correction.
1
Press and hold FUNC./SETUP for at least 2
seconds to setup the Selection mode.
2
Turn the Rotary encoder to select AUDIO mode,
and then press
/
Bluetooth
GENERAL
*
TUNER
Bluetooth
* Only when HD Radio/SAT Radio is connected.
3
Turn the Rotary encoder to select T.CORR
Parameter mode, and then press
4
Turn the Rotary encoder to select the desired
items, and then press
T.CORR Parameter<cm>
(Initial setting)
5
After setting, press and hold FUNC./SETUP for at
least 2 seconds to return to normal mode.
• Pressing
/RTN during the procedure will return to the previous
mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is canceled.
ESC
• Press and hold
/
for at least 2 seconds, the setting mode is
canceled.
Adjusting and Storing the Time Correction
Before performing the following procedures, refer to "About Time
Correction" (page 17).
1
Press A.SEL to recall the DSP adjust mode.
Media Xpander
Crossover
Parametric EQ/Graphic EQ
2
Turn the Rotary encoder to select the
T.Correction mode, and then press
3
Press BAND to select a speaker to be adjusted.
2.2ch (3WAY) System
L-F (Initial setting)
R-F
(Mid-L)
(Mid-R)
L-SW
R-SW
L-F
(Mid-L)
4.2ch (F/R/Sub-W) System
L-F (Initial setting)
R-F
(Front-L)
(Front-R) (Rear-L)
L-SW
R-SW
L-F
(Front-L)
/ENT.
AUDIO
DISPLAY
/
/ENT.
/
/ENT.
T.CORR Parameter<inch>
T.Correction
Media Xpander
/
/ENT.
L-R
R-R
(High-L ) (High-R)
L-R
R-R
(Rear-R)
Publicité
Chapitres
Table des Matières
