Technical Data; Noise/Vibration Information - Bosch PTK 14E Notice Originale

OBJ_BUCH-109-004.book Page 11 Monday, March 18, 2013 11:00 AM
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Trigger
2 Thumbwheel for hammer-force preselection
3 Magazine slider
4 Latching aperture for support foot
5 Latching aperture for spacer clamp
6 Latching aperture for stapler plate
7 Tacker head
8 Selector switch for DuoTac-Automatic
9 Nail strip*
10 Staple strip*
11 Magazine
12 Support foot*
13 Stapler plate*
14 Spacer clamp*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Tacker
Article number
Impact rate
Intermittent operation
Staple width
Staple length
Nails
Magazine capacity, max.
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 87 dB(A); Sound power level 98 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a and uncertainty K determined ac-
h
cording to EN 60745:
2 2
a = 6.6 m/s , K= 1.5 m/s .
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
Bosch Power Tools
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
PTK 14 E
Robert Bosch GmbH, Power Tools Division
0 603 265 2..
D-70745 Leinfelden-Echterdingen
-1
min 30
18.03.2013
min 15
Assembly
mm 11.4
mm 6 – 14
Loading the Magazine (see figure A)
mm 14
 Before any work on the machine itself, pull the mains
100
plug.
 Use only original Bosch accessories. The precision com-
kg 1.1
ponents of the tacker, such as magazine, striker and im-
/II
pact channel, are adapted for Bosch staples, nails or pins.
Other manufacturers use different steel qualities and
measures.
–
–
–
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
(1) Press on both sides of the magazine slider 3 and pull
out the magazine 11.
(2) Insert the staple strip 10 or the nail strip 9. Hold the
tacker at a slight angle when inserting the nail strip 9, so
that the nails face against the sidewall.
(3) Slide in the magazine 11 until the closure on the mag-
azine slider 3 engages.
1 609 92A 093 | (18.3.13)
English | 11