Noise/Vibration Information; Declaration Of Conformity - Bosch GEX 125 A Professional Notice Originale

OBJ_BUCH-424-006.book Page 14 Monday, August 22, 2016 10:24 AM
14 | English
Random Orbital Sander
GEX ...
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is 75 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a = 4.0 m/s , K= 1.5 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745,
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:
Material
– Paint
– Varnish
– Filling compound
– Filler
1 609 92A 2PF | (22.8.16)
125 A 125 AC
kg 1.9 2.0
/II /II
EN 50581according to the provisions of the directives
2011/65/EU, 2014/30/EU, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
D-70538 Stuttgart
Henk Becker
Executive Vice President
Engineering
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
 Before any work on the machine itself, pull the mains
plug.
Replacing the Sanding Sheet (see figure A)
When attaching a new sanding sheet, remove any dust or de-
bris from the sanding plate 8, e. g., with a brush.
The surface of the sanding plate 8 is fitted with Velcro backing
for quick and easy fastening of sanding sheets with Velcro ad-
hesion.
Press the sanding sheet 10 firmly against the bottom side of
the sanding plate 8.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
Application
For sanding off paint
For sanding primer (e. g., for removing brush dashes,
drops of paint and paint run)
For final sanding of primers before coating
125 AC 150 AC
2.0 2.1
/II /II
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Grain size
coarse
medium
fine
Bosch Power Tools
150 AC
2.1
/II
40
60
80
100
120
180
240
320
400