Battery Charging; Dust/Chip Extraction; Starting Operation - Bosch EasyCut 12 NanoBlade Notice Originale

OBJ_BUCH-3083-001.book Page 14 Friday, December 16, 2016 12:39 PM
14 | English
Assembly
 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.), remove the battery from the
power tool. There is danger of injury when unintentionally
actuating the On/Off switch.

Battery Charging

 Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
Selecting a Saw Blade
 Use only clean saw blades. Ensure that the SDS saw
blade holder is also free of chips and sawdust.
Use only saw blades suitable for the material being worked.
The saw blade should not be longer than required for the in-
tended cut.
Saw blade
Nanoblade Wood Basic
Nanoblade Wood Speed
Nanoblade Hardwood Basic
Nanoblade Wood Speed
Inserting the Saw Blade (see figure B)
Use the lever 10 to open the cover 9 of the SDS saw blade re-
ceptacle. Insert the saw blade as shown in the illustration. En-
sure that the drive shaft and the end of the saw blade fit in the
recess of the SDS saw blade receptacle 12. Close the cover of
the SDS saw blade receptacle 9 and lock it using the locking
lever of the SDS saw blade receptacle 10 until it can be heard
to engage.
The chain of the saw blade is automatically tensioned.
If the chain slips through or becomes detached from the guide
unit, open and close the cover of the saw blade receptacle.
Removing the Saw Blade
Open the locking lever 10 and fold the cover of the SDS saw
blade receptacle 9 fully upward. Remove the saw blade.

Dust/Chip Extraction

 Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
1 609 92A 3R2 | (16.12.16)
Inserting/Removing the Battery (see figure A)
Insert the battery into the machine as shown. The battery
must be felt to engage.
To remove the battery 5, press the unlocking buttons 6 and
pull the battery out of the machine to the rear. Do not exert
any force.
Inserting/Replacing the Saw Blade (see figure B)
 When changing the saw blade, do not hold the tool with
one hand on or around the On/Off switch and lock off.
There is danger of injury when the On/Off switch is unin-
tentionally actuated.
 When mounting or changing the saw blade, wear pro-
tective gloves. Application tools are sharp and can be-
come hot when used for prolonged periods of time.
 Do not pull on the chain and do not pull the chain off the
guide unit!
 Always replace a complete saw blade with a complete
saw blade! The chain cannot be replaced on its own.
 Avoid skin contact when you want to replace a saw
blade and wear protective gloves. The saw blade can be-
come hot during prolonged use.
Cutting depth Part number
50 mm 2 609 256 D83
50 mm 2 609 256 D84
50 mm 2 609 256 D85
65 mm 2 609 256 D86
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dust can
easily ignite.
Operation
 Never bend the saw blade!

Starting Operation

Inserting the battery
Note: Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
Insert the charged battery 5 into the handle until it can be felt
to engage and faces flush against the handle.
Materials
Wood, Plastic (PVC, PC, PMMA)
Wood, Plastic (PVC, PC, PMMA)
Hardwood, Plastic (PVC, PC, PMMA)
Wood, Plastic (PVC, PC, PMMA)
Bosch Power Tools