I Feel - Mitsubishi Electric MS-A18WV Notice D'utilisation

I FEEL... AUTO OPERATION
With the " (I FEEL...)" auto operation mode, the optimum room condition can be set automatically
with a one-touch operation.
To start operation:
I
Press the
˚C
CLOCK
When the "
AMPM
controlled at the optimum temperature.
AMPM
To stop operation:
TOO TOO
ON/OFF
WARM COOL
I
Press the
FAN STOP
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
I FEEL COOL
VANE START
HEAT DRY
If you feel slightly warm:
I
MODE WIDE VANE HR.
ECONO COOL LONG MIN.
RESET CLOCK
If you feel slightly cool:
I
When " (I FEEL...)" is not selected, press the
button until it is set.
Each time the button is pressed, the operation mode is changed
(I FEEL...) → (COOL) → (DRY) →
in sequence:
(HEAT: MSH series)/ (FAN: MS series)
Description of "AUTO RESTART FUNCTION"
• These units are equipped with an auto restart function. When the main power is turned on, the air conditioner will start
operation automatically in the same mode as the one set with the remote controller before the shutoff of the main
power.
• If the unit was set to off with the remote controller before the shutoff of the main power, it will remain stopped even after
the main power is turned on.
• If the unit was in the emergency operation before the shutoff of the main power, it will start operation, when main power
comes on, in the same mode as the one set with the remote controller before the emergency operation.
• If the unit is operated in "I FEEL..." mode before power failure, the operation is not stored in the memory. In "I FEEL..."
mode, the operation is decided by the initial room temperature at (re)start.
6
ON/OFF
button.
(I FEEL...)" mode is selected, the air conditioner is automatically
ON/OFF
button.
TOO
WARM
Press the button to lower the temperature.
One press lowers the temperature by about 1°C.
TOO
COOL
Press the button to raise the temperature.
One press raises the temperature by about 1°C.
MODE
FAN
I FEEL COOL
VANE
HEAT
DRY
MODE WIDE VANE
ECONO COOL LONG
Description of "I FEEL..." mode
Details of operation
According to the room temperature when the operation starts, the operation mode is automatically set to COOL, DRY or
HEAT. However, when operation is started again within 2 hours after it is stopped, the same operation mode before the
operation is stopped is selected. The operation mode selected first is not changed even if the room temperature changes.
If the operation mode does not match the room condition, select the appropriate operation mode by pressing the
button.
Details of auto operation
Room temperature
when started
About 25°C or higher
About 25°C - 23°C
About 23°C or lower
NOTE:
COOL: When the room temperature is 2°C higher than the set temperature, the set temperature may not be
changed since the air conditioner is operating to reach the target (set) temperature. In this case, please
wait until the room temperature drops to within 2°C of the set temperature and then change the set
temperature.
HEAT: When the room temperature is 2°C lower than the set temperature, the set temperature may not be
changed since the air conditioner is operating to reach the target (set) temperature. In this case, please
wait until the room temperature rises to within 2°C of the set temperature and then change the set
temperature.
STOP
Details of display on the indoor unit
START
The operation indicator at the right side of the indoor unit indicates the operation state.
HR.
Operation Indicator
MIN.
Operation indicator lamp
Indication
COOL & HEAT type (MSH series) COOL ONLY type (MS series)
Operation mode Target temperature Operation mode
(initial state)
COOL About 24°C COOL
DRY — DRY
HEAT About 26°C DRY
Lighted
Blinking
Not lighted
Operation state
This shows that the air conditioner is operating to reach the
target temperature. Please wait until the target temperature
is obtained.
This shows that the room temperature is approaching the
target temperature.
(In case of outdoor unit MXZ series only)
Please refer to Information for multi system air conditioner.
(Page 7)
MODE
Target temperature
(initial state)
About 24°C
—
—
Difference between target
temperature and room temperature
About 2°C or more
About 2°C or less
—